manualshive.com logo in svg

Bosch PRAESENSA PRA-AD604, Руководство по настройке, Страница: 110 / 164

Поделиться
Скачать
Bosch PRAESENSA PRA-AD604 Скачать руководство пользователя страница 110

110

en | Diagnose

PRAESENSA

2020-09 | V1.20 | PRAESENSA 1.20

Configuration manual

Bosch Security Systems B.V.

6.4

Amplifier spare channel

The Amplifier spare channel page in the Diagnose section is used to generate a fault in an
amplifier output channel to force it to the spare output channel of the selected amplifier.
This function can be used to test the sparing and faults behavior in an installation (e.g. during
commissioning and/or certification of an installation).
The following information is presented on the Amplifier spare channel page:

Item

Description

Name

Shows

 the name of each amplifier added to the system. See 

Add a

device, page 41.

Faulty channel

Click and select 

the (faulty) amplifier channel which need to be forced

routed via the spare amplifier channel. See 

Amplifier, page 48.

Apply

Click

 the 

Apply

 button to set and activate the forced spare channel

switching of the selected amplifier (channel) in the system. See
Amplifier, page 48 > Front and rear panel indicators.

Notice!

To deactivate the spare channel switching: select “None” below Faulty channel, click the
corresponding Apply button, and acknowledge and reset the fault (See 

Assigning a function,

page 85 > acknowledge and/or reset).

Refer to

–

Add a device, page 41

–

Amplifier, page 48

–

Troubleshooting, page 133

Содержание PRAESENSA PRA-AD604





































































































































































Отзывы:

Нет отзывов