manualshive.com logo in svg

Bosch PRAESENSA PRA-AD604, Руководство по настройке, Страница: 48 / 164

Поделиться
Скачать
Bosch PRAESENSA PRA-AD604 Скачать руководство пользователя страница 48

48

en | Configure the system

PRAESENSA

2020-09 | V1.20 | PRAESENSA 1.20

Configuration manual

Bosch Security Systems B.V.

5.3.2

Amplifier

1.

Below

 Device options, 

clic

k Amplifier:

–

A new screen appears listed the connected amplifier(s).

–

Notice that an amplifier is only listed when it is added to the System composition.

2.

Select and click

 the amplifier name to configure:

–

A new screen appears to configure General and Audio outputs functionality.

General

1.

Select and click

 the + of the General category row:

2.

Select

, 

enable

 or 

disable

 each of the following items:

Item

Value

Description

Supervision 

(per amplifier)

Supervision of the amplifier power supply, ground connection and lifeline

.

Power supply

Enable / Disable

Enable:

 48 Vdc amplifier power supply (1‑3)

input. The amplifier front/rear panel indicator
will indicate faults and/or power loss (see
indicators tables at the end of this section),
Diagnose, page 105 and Optional: Using the
Logging Viewer, page 125

Disable:

 (unchecked), results in a system that

does not detect Power supply input failures
of the amplifier disabled input.

Ground leakage

Enable / Disable

Enable: 

ground shorts will be indicated by

the amplifier front/rear panel indicator(s)
(see indicator tables following), 

Diagnose,

page 105 and Optional: Using the Logging
Viewer, page 125

Disable

 (unchecked), results in a system that

does not detect Ground Leakage failures of
the amplifier.

Lifeline supply input

Enable / Disable

Enable: 

lifeline power supply loss will be

reported. See 

Diagnose, page 105 and

Optional: Using the Logging Viewer, page 125

Submit

Button

Click

 the Submit button to store the settings.

Notice that you always have to Save the
configuration. See 

Save configuration, page

102

Содержание PRAESENSA PRA-AD604





































































































































































Отзывы:

Нет отзывов