Bosch Mac Tools Mentor Touch ET650, Руководство по эксплуатации

Страница: 15 / 24

1 689 989 240 2015-09-25
|
Robert Bosch GmbH
Initial commissioning | ET750 | 15 en
5.3 Configuration of the operating system
i
If the storage battery in the ET750 has not been
charged, supply the ET750 with voltage using the
power supply unit.
1. Switch on the ET750.
i
The first time that you start Windows, the ET750
screen can remain black for up to four minutes. Dur-
ing this time it is evident that the ET750 is switched
on and Windows is starting up by the flashing LED
of the on/off button.
!
Never turn off the ET750 during this time! Wait until
the Windows start screen appears.
2. After switching on for the first time, use the lan-
guage selection menu to select the Windows operat-
ing system language and follow the message.
i
There is no provision for subsequent alteration of the
Windows operating system language. Should this nev-
ertheless become necessary, the language selection
menu can be re-started under
"Start >> All programs
>> Tools >> Localization".
5.4 Starting the HUB
1. Start the HUB.
 The dialog box "Language and Country" opens.
2. Choose language and country and continue the
installation with <
Next >.
3. Read and accept the user agreement and warranty.
4. Heed and follow the instructions on the screen.
"
HUB is started.
HUB has to communicate with ET650 for control unit
diagnosis. To do so, the ET650 must be supplied with
voltage via the power supply unit included in the scope
of delivery or via the OBD interface in the vehicle. A
Bluetooth connection has been configured ex-works
between the ET750 and the ET650.
i
To access all HUB functions and to receive software
updates, HUB must be licensed. Licensing can be
performed either online or with a license file. The
further licensing procedure for initial commissioning
is described in detail in the HUB online help (
).
6. Operation ET750
6.1 Switching on the ET750
!
To avoid the formation of condensed water, allow
the ET750 to adjust to ambient temperature before
switching on the ET750!
1. Switch on the ET750 by pressing the On/Off button .
 After the Windows operating system has been
run up, the start mask appears.
2. Use the stylus to touch the application you would
like to work with.
Druckdatum/ print date: 17.12.2010
Weitergabe sowie Vervielfältigung der Zeich-
nungen sind nicht gestattet und müssen
streng vertraulich behandelt werden. Alle
Rechte sind bei ads-tec GmbH nach DIN 34.
strictly confidential according to DIN 34. File:Airbag L TT13 Doku 130
( )
Rz 10
CAUTION – Risk of injury from triggering
the airbag with attached ET750!
If the ET750 is attached to (suspended from)
the steering wheel, injuries could result from
unintentionally triggering the airbag.
¶
Never attach the ET750 to the steering
wheel.
6.2 Switching off the ET750
1. Press the function key f.
 The home page and task bar are opened.
2. Select < Shutdown > from the home page.
 Windows is shut down.
"
The ET750 is switched off.
i
Pressing the On/Off button for > 2 seconds shuts
down the Windows operating system and switches
off the ET750.
i
Pressing the On/Off button for > 12 seconds
switches off the ET750 without first shutting down
the operating system. This mode should only be used
if shutting down the Windows operating system is
not possible.
6.3 Setting power options
The menu " Start >> Control panel >> Power options " can
be used to select and alter the power plan (e.g. the moni-
tor switch-off time or the display brightness setting).