ICP-CC488 |
User's Guide | 10.
Date and Time
EN
| 13
Bosch Security Systems, Inc. | 12/08 | F01U089456-02
9.1 Fault
Descriptions
1 System
Fault
A system fault only displays when any of
the following faults occur. After entering
Fault Analysis Mode, press and hold the [1]
key to determine which of the following
faults occurred.
Low Battery Fault
– A low battery fault
registers when the system detects a low
capacity back-up battery. The system
automatically performs a battery test every
four hours and every time you arm the
system.
Date and Time
– The date and time fault
registers every time the system is powered
down. This type of fault does not cause the
FAULT indicator to display on the codepad
unless your installer programmed the
automatic arming time. Refer to
Section 10.
Date and Time
on page 13 to program the
date and time.
RF Receiver Fail
– The RF receiver fault
registers once the system detects that the
wireless receiver unit is disconnected.
Horn Speaker Fail
– This fault registers
when the system detects that the horn
speaker is disconnected. This fault clears
once the horn speaker is reconnected. Your
installer must program the system for this
feature to operate.
Telephone Line Fail
– A telephone line
fault registers when the system detects that
the telephone line is disconnected from the
control panel. Your installer must program
the system for this feature to operate.
EEPROM Fail
– An EEPROM fail registers
when the system detects an internal
checksum error. Contact your installer as
soon as this fault displays.
AUX Power Supply Fail
– This fault
occurs when either of the two 1 A AUX
power supplies fails. Contact your installer
as soon as this fault displays.
2
RF Low Battery
This fault occurs when any of the RF
wireless devices report a low battery
condition to the control panel. While in
Fault Analysis Mode, press and hold the [2]
key until two beeps sound. This displays the
zone reporting the RF Low Battery fault.
3
Zone Tamper Fail
This fault occurs when any zone becomes
an open circuit. Press and hold the [3] key
until two beeps sound. This displays the
zone reporting the tamper fail fault.
4
Sensor Watch Fault
A sensor watch fault registers because one
or more detection devices failed to detect
any movement during the disarmed state
for the time period programmed by your
installer. The fault clears once the zone in
question detects movement and resets.
Press and hold the [4] key until two beeps
sound. This displays the zone reporting the
sensor watch fault.
5
RF Sensor Watch
An RF sensor watch fault registers because
one or more RF detection devices fails to
communicate to the RF radio receiver for
the time period programmed by your
installer. The fault clears once the RF
device in question successfully transmits to
the RF radio receiver.
Press and hold the [5] key until two beeps
sound. This displays the RF detection
device reporting the RF sensor watch fault.
6 Communication
Fail
A communication fail registers when the
control panel fails to communicate with the
receiving party (such as a monitoring
company, mobile phone, or pocket pager).
The communication fault clears once the
control panel successfully reports to the
receiving party.
To determine which receiver failed to
communicate, press and hold the [6] key.
10. Date and Time
Programming the date and time is only required
when you need functions such as automatic test
reports, automatic arming, and history events to
operate correctly.
How to Program the Date and Time
1.
Enter your four character Master Code, followed
by [6] and the [#] key (for example, [25806#]).
Three beeps sound, and the STAY and AWAY
indicators flash.
2.
Enter the day, month, year, hour, and minute
(DD, MM, YY, HH, MM format) (for example,
DD = day of the month, MM = month of the
year, YY = current year, HH = hour of the day,
MM = minute of the day).
To program the hour of the day, use the 24:00
hour format.
