Bosch HSG936A 1 Series, Руководство пользователя и инструкции по установке

Страница: 29 / 56

Drying
en
29
Descaling comprises several steps and takes
approximately 70 - 95 minutes:
¡
Descaling (approx. 55 - 70 minutes)
¡
First rinse cycle (approx. 8 - 12 minutes)
¡
Second rinse cycle (approx. 8 - 12 minutes)
For reasons of hygiene, the descaling programme must
be run in full.
If descaling is interrupted, you can no longer set any
operation. To ensure that the appliance is ready for op-
eration again, carry out 2 rinse cycles.
19.1 Preparing descaling
ATTENTION!
The length of time for which the descaler is left to work
is based on the recommended, liquid descaler. Other
descalers may damage the appliance.
▶
Only use the liquid descaler recommended by us
for the descaling programme.
If descaling solution comes into contact with the control
panel or other delicate surfaces, it will damage them.
▶
Remove descaling solution immediately with water.
1.
Mix the descaling solution:
‒
200 ml liquid descaler
‒
400 ml water
2.
Open the control panel.
3.
Remove the water tank and fill it with descaling solu-
tion.
4.
Once the descaling solution has been poured into
the water tank, slide the tank back in.
5.
Close the control panel.
19.2 Setting the descaling programme
Requirement:
→ "Preparing descaling", Page 29
1.
Press "Cleaning" in the menu.
2.
Press ​⁠"Descaling".
The duration cannot be changed.
3.
Press ​⁠.
a
A notification stating that you should carry out the
necessary preparatory work for descaling appears
on the display.
4. Confirm the message.
a
The descaling programme starts and the duration
counts down.
a
Once the first part of the descaling programme has
finished, a signal tone sounds. The appliance
prompts you to rinse twice.
5. To rinse the appliance, for each rinse cycle:
‒
Open the control panel and remove the water
tank.
‒
Thoroughly rinse the water tank and fill it with
fresh water.
‒
Slide in the water tank and close the control
panel.
a
A signal tone sounds when each rinse cycle has
ended.
6.
Once the second rinse cycle is complete:
‒
Empty and dry the water tank.
→
"Emptying the water tank", Page 20
‒
Press ​⁠ to switch the appliance off.
20 Drying
To prevent residual moisture , dry the cooking compart-
ment following operation with steam and after using the
cleaning aid.
ATTENTION!
If there is water on the cooking compartment floor
when operating the appliance at temperatures above
120 °C, this will damage the enamel.
▶
Do not use the appliance if there is water on the
cooking compartment floor.
▶
Wipe away any water on the cooking compartment
floor before operation.
20.1 Drying the cooking compartment
You can leave the cooking compartment to dry or use
the drying function.
1.
Allow the appliance to cool down.
2.
Remove any dirt from the cooking compartment.
3.
Wipe away any water in the cooking compartment.
4.
Dry the cooking compartment.
‒
To dry the cooking compartment, leave the appli-
ance door open for 1 hour.
‒
To use the drying function, set "Drying function".
→
"Setting the drying process", Page 29
Setting the drying process
Requirement:
→ "Drying the cooking compartment",
Page 29
1.
Press "Cleaning" in the menu.
2. Press ​⁠ "Drying function".
The duration cannot be changed.
3. Press ​⁠.
a
A notification stating that you should carry out the
necessary preparatory work for the drying appears
on the display.
4.
Confirm the message.
a
The drying process starts and the duration counts
down.
a
Once the drying has ended, a signal tone sounds. A
message appears on the display confirming that the
operation has finished.
5.
Press ​⁠ to switch the appliance off.
6.
To dry the cooking compartment completely, leave
the appliance door open for 1 to 2 minutes.
21 Appliance door
To clean the appliance door thoroughly, you can disas-
semble the appliance door.
Note:
Wipe the condensate trough without pressure.