Bosch HMT75G421R, Инструкция по эксплуатации

Страница: 25 / 36

25
■
You cannot save automatic programmes.
■
You can save the memory settings and start the appliance
immediately. When finishing, instead of pressing i , press
Start.
■
Saving a new setting in the memory:
press the i button. The
old settings appear. Save the new programme as described
in steps 1-4.
Starting the memory
It is very easy to start the saved programme. Place your meal
into the appliance. Close the appliance door.
1.
Press the i button.
The saved settings are displayed.
2.
Press the Start button.
The cooking time counts down in the display.
The cooking time has elapsed
A signal sounds. Open the appliance door or press Stop. The
clock reappears.
Pausing
Press the Stop button once, or open the appliance door. Press
the START button after closing the door.
Cancelling the setting
Press the Stop button twice, or open the appliance door and
press the Stop button once.
Changing the signal duration
You will hear a signal when the appliance is switched off. You
can change the duration of the acoustic signal.
Press the Start button for approx. 6 seconds.
The new signal duration is adopted.
The clock reappears.
The following are possible:
Short signal duration - 3 tones
Long signal duration - 30 tones.
Care and cleaning
With careful care and cleaning your microwave oven will retain
its looks and remain good order. We will explain here how you
should care for and clean your appliance correctly.
:
Risk of short circuit!
Never use high-pressure cleaners or steam cleaners to clean
the oven.
:
Risk of burns!
Never clean the appliance immediately after switching off. Let
the appliance cool down.
:
Risk of electric shock!
Do not immerse the appliance in water or clean under a jet of
water.
Surfaces are different, and damage caused by using the wrong
cleaning agent can be avoided by observing the information in
the table below.
Do not use
■
sharp or abrasive cleaning agents.
The surface could be damaged. If such a substance comes
into contact with the front of the appliance, wash it off
immediately with water.
■
metal or glass scrapers to clean the glass in the appliance
door.
■
metal or glass scrapers for cleaning the seal.
■
hard scouring pads or cleaning sponges.
Wash new sponge cloths thoroughly before use.
■
cleaning agents with high concentrations of alcohol.
Cleaning agents
Caution!
Before cleaning, unplug the appliance from the mains or switch
off the circuit breaker in the fuse box. Clean the outside of the
appliance and the cooking compartment with a damp cloth and
mild detergent. Dry with a clean cloth.
Area Cleaning agents
Appliance front Hot soapy water:
Clean with a dish cloth and dry with a soft
cloth. Do not use glass cleaners or metal
or glass scrapers for cleaning.
Appliance front
with stainless steel
Hot soapy water:
Clean with a dish cloth and dry with a soft
cloth. Remove flecks of limescale, grease,
starch and albumin (e.g. egg white) imme-
diately. Corrosion can form under such
residues. Special stainless steel cleaning
agents can be obtained from the after-
sales service or from specialist shops. Do
not use glass cleaners or metal or glass
scrapers for cleaning.
Cooking compart-
ment made of
stainless steel
Hot soapy water or a vinegar solution:
Clean with a dish cloth and dry with a soft
cloth.
If the oven is very dirty: use oven cleaner,
but only when cooking compartment is
cold. It is best to use a stainless-steel
sponge. Do not use oven spray or other
aggressive oven cleaners or abrasive
materials. Scouring pads, rough sponges
and pan cleaners are also unsuitable.
These items scratch the surface. Allow the
interior surfaces to dry thoroughly.
Recess in cook-
ing compartment
Damp cloth:
Ensure that no water seeps through the
turntable drive into the appliance interior.
Turntable and turn-
table ring
Hot soapy water:
When putting the turntable back in place,
make sure it slots in correctly.
Wire rack Hot soapy water:
Clean using stainless steel cleaning agent
or in the dishwasher.
Door panels Glass cleaner:
Clean with a dish cloth. Do not use a
glass scraper.