Bosch GRO 12V-35 Скачать руководство пользователя страница 18

Страница: 18 / 259

| English

The stated vibration level applies to the main applications of
the power tool. However, if the power tool is used for differ-
ent applications, with different application tools or poorly
maintained, the vibration level may differ. This can signific-
antly increase the exposure to vibration over the total work-
ing period.
To estimate the exposure to vibration accurately, the times
when the tool is switched off or when it is running but not ac-
tually being used should also be taken into account. This can
significantly reduce the exposure to vibration over the total
working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping the hands warm,
and organising workflows correctly.

Fitting

Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage.

There is risk of injury

from unintentionally pressing the on/off switch.

Charging the Battery

Use only the chargers listed in the technical data.

Only

these chargers are matched to the lithium-ion battery of
your power tool.

Note:

The battery is supplied partially charged. To ensure

full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.

Do not continue to press the On/Off switch after the
power tool has automatically switched off.

The battery

can be damaged.

Follow the instructions on correct disposal.

Removing the Battery (see figure A)

To remove the battery

(9)

, press the release button

(16)

and pull the battery to the rear and out of the power tool.

not use force to do this.

Battery charge indicator

The three green LEDs of the battery charge indicator

(8)

in-

dicate the state of charge of the battery

(9)

LEDs

Meaning

3 × continuous green light 60−100%

2 × continuous green light 30−60%

1 × continuous green light 5−30%

1 × flashing green light

0−5%

LEDs

Meaning

1 × continuous red light

Power tool has overheated!

– Switch the power tool off and

allow it to cool down com-
pletely.

1 × flashing red light

Power tool has overloaded!

– Exert less pressure on the

workpiece during work.

Changing the Tool

When inserting an application tool, ensure that the
shank of the application tool is firmly seated in the
tool holder.

When the shank of the application tool is not

inserted deep enough in the tool holder, the application
tool can become loose again and cannot be controlled.

Do not use application tools that are worn or in other-
wise less than perfect condition.

Defective application

tools can break, for example, causing material damage
and personal injury.

Only use brand accessories for grinding, sanding,
brushing, polishing, routing and cut-off grinding from
the dealer for the power tool, which are approved for
a speed of 35,000 min

-1

and which have a shank with

an outside diameter of 3.2 mm.

Inserting the Application Tool (see figure B)

– Press the spindle lock

(5)

and turn the clamping nut

(12)

by hand until locked.

– Press and hold the spindle lock and loosen the clamping

nut

(12)

with the open-ended spanner

(17)

by turning it

anticlockwise.

– Insert the dust-free application tool (e.g. holding rod

(2)

grinding accessory

(3)

or drill bit) into the tool holder

(13)

of the collet

(19)

Note:

Ensure that the shank

(18)

of the application tool sits

in as far as possible, but at least 10 mm into the collet.
– Press and hold the spindle lock

(5)

and tighten the applic-

ation tool by turning the clamping nut

(12)

clockwise with

the open-ended spanner

(17)

Removing the application tool

– Loosen the clamping nut

(12)

as previously described

and remove the application tool.

Fitting the Cutting Disc (see figure C)

Cutting discs reinforced with fibreglass are included in the
scope of delivery. They can be used for grooving, routing and
cutting metal, wood and plastic.
– Insert the holding rod

(2)

into the tool holder (see "Insert-

ing the Application Tool (see figure

)", page 18).

– Press and hold the spindle lock

(5)

and completely un-

screw the screw on the holding rod

(2)

using the screw-

driver

(17)