Bosch Greentherm 9800 SECO 199 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 52

background image

6 720 817 281 (2017/05)

Greentherm 9800 SEO 160/199 | SECO 199

6 | Appliance details

BOSCH water heater complies with the State of California Lead
Law (AB1953).

3

Appliance details

3.1

Features

Residential / Commercial models
•

Greentherm 9800 SEO residential models
– maximum temperature 120 °F

1)

•

Greentherm 9800 SECO commercial models
– maximum temperature 180 °F

Parts
•

High power segmented burner with low NOx emissions.

•

Modulating gas valve with pressure regulator.

•

Modulating water valve.

•

Active bypass water valve for quick response to changing
water flows.

•

Burner power segmentation with modulation range from
1:22.

High quality materials for long working life
•

Copper heat exchanger.

•

Stainless Steel 316L condensing heat exchanger

Features

•

Compact space saver: mounts on a wall with a supplied
bracket.

•

Easy minimum to achieve low output power.

•

Opti-flow that auto adjusts unit for easy installation.

•

Easily removable one-piece cover.

•

On/Off and Temperature remote control.

•

Program button (Selectable temperature default).

•

Failure codes for easy diagnostics and repair.

•

Real-time diagnostics for troubleshooting/informational
purposes.

•

Built in freeze protection.

•

Integrated siphon to limit condensate freezing in external
condensate pipes.

Note: The freeze prevention kit is designed to provide
protection for the water heater down to

approximately -4 °F

for short term conditions only

. It will not protect the

appliance in areas where the temperature is routinely expected
to be below freezing.
- The freeze prevention kit will not protect plumbing outside the
appliance from freezing. Precautions should be taken.

Accessories (Bosch part #)
•

Neutralizer Kit (7738001483)

•

Wi-Fi module [802.11 b/g/n (2.4 GHz)]

•

Aquastat kit (7736504584)

•

Recirculation pump kit (7736504585)

•

Tank loading NTC (7736504583)

1) Source: Moritz, A.R. and Henriques, F.C., Jr. (1947).

Studies of thermal injury. II. The relative importance of
time and surface temperature in the causation of
cutaneous burns, Am J of Pathol, 23, 695-720.

WARNING:

California Proposition 65

The California Safe Drinking Water and Toxic
Enforcement Act requires the Governor of
California to publish a list of substances
known to the State of California to cause
cancer, birth defects, or other reproductive
harm, and requires businesses to warn of
potential exposure to such substances.

▶ This product contains chemicals known

to the State of California to cause
cancer, birth defects, or other
reproductive harm. This appliance can
cause low-level exposure to some of the
substances included in the Act.

1) Can be programmed to achieve 140 °F

BOSCH is constantly improving its products,
therefore specifications are subject to
change without prior notice.

«
...
4
5
6
7
8
...
»

Содержание Greentherm 9800 SECO 199





















































Отзывы:

Нет отзывов

Похожие инструкции для Greentherm 9800 SECO 199

Бренд: umbra pompe Страницы: 16

Бренд: A.O. Smith Страницы: 2

Бренд: salmson Страницы: 16

Бренд: Eliz Страницы: 20

Бренд: HeatStar Страницы: 60

Бренд: PerformancePro Страницы: 15

Бренд: T.I.P. Страницы: 136

Бренд: Speck pumpen Страницы: 8

Бренд: DELEX Страницы: 7

Бренд: kbice Страницы: 19

Бренд: CareFusion Страницы: 28

Бренд: Hortus Страницы: 12

Бренд: Penguin Страницы: 10

Бренд: Gordon-Ray Страницы: 20

HotZone Patio Heater

Бренд: Schaefer Страницы: 12

Бренд: Wilo Страницы: 20

Whale Expanse DW0801U

Бренд: Munster Simms Engineering Ltd. Страницы: 27

GARDEN-SP-CEA-CA

Бренд: Lowara Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды