Bosch Greentherm 9800 SECO 199 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 52

background image

6 720 817 281 (2017/05)

Greentherm 9800 SEO 160/199 | SECO 199

Installation for modular homes | 15

5

Installation for modular homes

5.1

Mounting installation for modular homes

When installing this appliance on the outside of a modular
home, the unit must be additionally secured at the bottom of
the water heater as shown in fig. 9. Use the included screws to
secure the brackets at the bottom of the water heater to the
wall. If the wall is sheathed with plaster or drywall, it is
recommended that a support board be first attached across a
pair of studs at the bottom of the unit as shown in fig. 6.

Fig. 9

Mounting the heater on modular homes

6

Installation instructions

6.1

Gas piping & connections

Before connecting the gas supply, check the rating plate on the
right side of the heater to be sure that the heater is rated for the
same gas to which it will be connected.
In the United States: The installation must conform with local
codes or, in the absence of local codes, the National Fuel Gas
Code ANSI Z223.1/NFPA 54.
In Canada: The Installation must conform to CGA B149
INSTALLATION CODES and/or local installation codes.

GAS CONNECTIONS

▶ Install a manual gas shut off valve on the gas supply line

within easy reach of the appliance.

▶ Install a union when connecting the gas supply.
▶ Gas connection to the water heater is a ¾ " NPT. See

chapter 6.1.1 for the minimum internal pipe diameter
required.

▶ Undersized flexible appliance connector is not permitted.
▶ National Fuel Gas Code requires that a sediment trap (drip

leg) be installed on gas appliances not so equipped. The
drip leg must be accessible and not subject to freezing
conditions. Install in accordance with the
recommendations of the serving gas supplier, see fig. 11.

DANGER:

Explosion hazard!

▶ DO NOT connect to an unregulated or

high pressure propane line or to a high
pressure commercial natural gas line.

DANGER:

Explosion hazard!

▶ The heater must be isolated from the

gas supply piping system during any
pressure testing of that system at test
pressures equal to or more than 0.5
psig. If overpressure has occurred, such
as through improper testing of the gas
lines or malfunction of the supply
system, the gas valve must be checked
for safe operation.

«
...
13
14
15
16
17
...
»

Содержание Greentherm 9800 SECO 199





















































Отзывы:

Нет отзывов

Похожие инструкции для Greentherm 9800 SECO 199

Бренд: Calpeda Страницы: 80

Бренд: Dashan Страницы: 20

Бренд: EBARA Страницы: 40

Бренд: EBARA Страницы: 534

Бренд: EBARA Страницы: 60

Бренд: ebm-papst Страницы: 8

Бренд: Karibu Страницы: 60

Бренд: Park House Healthcare Страницы: 28

Бренд: Gude Страницы: 64

Бренд: Stübbe Страницы: 32

Sanitizer Plus ASP1-1044

Бренд: Water Right Страницы: 30

Бренд: Edwards Страницы: 56

Бренд: Greencut Страницы: 54

Бренд: Somogyi Страницы: 20

BC-F20HWR2-200L

Бренд: enertik Страницы: 33

MagicComfort MSH 300

Бренд: Waeco Страницы: 192

Бренд: Drazice Страницы: 9

Бренд: Danfoss Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды