Bosch Greentherm 9800 SECO 199 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 52

background image

6 720 817 281 (2017/05)

Greentherm 9800 SEO 160/199 | SECO 199

12 | Installation instructions

4

Installation instructions

4.1

Installation tools

The following specialized tools may be required for installation:

•

Manometer

•

Combustion Gas Analyzer

4.2

Introduction

Please follow these instructions. Failure to follow
instructions may result in:

▶ Damage or injury.
▶ Improper operation.
▶ Loss of warranty.

4.3

Proper location for installing your heater

Carefully select the location of the water heater. For your safety
and for proper heater operation, you must not block or obstruct
combustion air to the heater.
Follow the guidelines below:

1. Locate the heater where gas and plumbing connections are

feasible and convenient.

2. The hot water lines should be kept short and insulated to

save energy. It is recommended to locate the water heater
as close as practical to the most frequently used hot water
fixtures.

3. In areas where outside temperatures is below 32 °F (0 °C)

water pipes should be properly insulated, to maintain
water temperature and prevent freezing.

DANGER:

▶ The water heater must be installed by a

qualified installer in accordance with
these instructions. If improperly
installed, a hazardous condition such as
explosion or carbon monoxide
poisoning could result. Bosch
Thermotechnology Corp. is not
responsible for improperly installed
appliances.

Common installation practice is to first
determine the installation location, then
design the piping layout.

NOTICE:

Risk of appliance freezing!

▶ The water in this water heater is cold and

always remains cold except for the times
the burner is on. In the event of power
outage in conjunction with freezing
temperatures, the heater should be
drained.
See chapter 9.2, page 30 “Winterizing”
for draining instructions.

WARNING:

▶ Flammable materials, gasoline,

pressurized containers, or any other
items or articles that are potential fire
hazards must NOT be placed on or
adjacent to the heater. The appliance
area must be kept free of all combustible
materials, gasoline and other flammable
vapors and liquids.

«
...
10
11
12
13
14
...
»

Содержание Greentherm 9800 SECO 199





















































Отзывы:

Нет отзывов

Похожие инструкции для Greentherm 9800 SECO 199

Бренд: Gardena Страницы: 182

Бренд: Badu Tec Страницы: 98

Бренд: Jet-Line group Страницы: 20

Бренд: Danfoss Страницы: 26

Бренд: Calpeda Страницы: 80

Бренд: VEAB Страницы: 24

Бренд: Zoeller Страницы: 10

Бренд: Gardena Страницы: 16

Bell & Gossett ecocirc XL Series

Бренд: Xylem Страницы: 62

Бренд: Sicce Страницы: 24

Бренд: nedis Страницы: 36

Бренд: VEAB Страницы: 4

Бренд: Oceanic Страницы: 33

Бренд: ACDC Страницы: 3

Бренд: DèLonghi Страницы: 7

Бренд: Chromalox Страницы: 4

Бренд: Honda Страницы: 75

Sportline HydraCoach

Бренд: E&B Giftware Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды