Bosch FPP-RNAC-8A-4C Скачать руководство пользователя страница 22

Страница: 22 / 26

FPP-RNAC-8A-4C

Operation and Installation Guide | 5.0

FPP-RNAC-8A-4C Local Status Display

Bosch Security Systems, Inc. | 8/09 | F01U025431-02

Table 10: Local Status Display LED Functions (continued)

LED Label Color

Description

SYSTEM

Yellow

Blink Count

Description

TROUBLE

(The Trouble Relay activates or changes state.)

(display priority)

Any memory fault (RAM, FLASH, watchdog,
unexpected interruptions, stack corruption).

Power supply overvoltage.

Low battery or missing battery

Battery charger circuit trouble.

Auxiliary power overcurrent condition – the current is
measured at the Auxiliary Power Port output.

System overcurrent – The combined currents
measured at each NAC output together with the
Auxiliary Power Port output.

Power supply output voltage is low.

STEADY

The SYS TRBL LED and the Trouble Relay are
active when the Flash Programming module is
connected.

4 GROUND

FAULT

Yellow

Ground Fault - Indicates that the NAC output wiring is not connected properly to
an external source or ground.
The Trouble Relay is deactivated.

TRBL1

Yellow

Output 1 has an open or shorted EOL
The Trouble Relay is deactivated.

TRBL2

Yellow

Output 2 has an open or shorted EOL
The Trouble Relay is deactivated.

TRBL3

Yellow

Output 3 has an open or shorted EOL
The Trouble Relay is deactivated.

TRBL4

Yellow

Output 4 has an open or shorted EOL
The Trouble Relay is deactivated.

Figure 13: FPP-RNAC-8A-4C LEDs

INPUT ACTIVE

AC OK

SYSTEM TROUBLE

GROUND FAULT
TROUBLE 4
TROUBLE 3

TROUBLE 2

TROUBLE 1

Содержание FPP-RNAC-8A-4C



























Результаты поиска

Содержание FPP-RNAC-8A-4C

Отзывы:

Похожие инструкции для FPP-RNAC-8A-4C

Бренды по названию

Популярные бренды

Bosch FPP-RNAC-8A-4C, Руководство по эксплуатации и установке

Результаты поиска

Содержание FPP-RNAC-8A-4C

Отзывы:

Похожие инструкции для FPP-RNAC-8A-4C

Бренды по названию

Популярные бренды