Bosch EX40 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 36

background image

23

6.

TROUBLESHOOTING GUIDE

PROBLEM

POSSIBLE

CAUSE

LIKELY SOLUTION

No Video

1. Power
Supply:
-Connections

-Voltage
Range...

2. Video

Connections

Check input power connections
at the cable leads.
Check for loose wires.

If connected to DC, check input
voltage range of 10.8 – 26.4V.
If connected to AC, check input
voltage range of 10.8 – 26.4V.
Measure the voltage and current
at the Input Power Cable.
The current should be >.02A
and <1.0A.

Determine if wiring polarity at
“Video Connector” terminal
block is correct.
Check the cable and BNC
connector.

If still no video, connect the
camera directly to the monitor.
Check the video signal. If okay,
the problem is with the
interconnections. If still no
video, contact BOSCH Service
Center. See rear page of this
manual for contact information.

«
...
27
28
29
30
31
...
»

Содержание EX40





































Отзывы:

Нет отзывов

Похожие инструкции для EX40

Бренд: D-Link Страницы: 72

Бренд: D-Link Страницы: 73

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 67

Бренд: D-Link Страницы: 24

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 2

DCS-2121 - SECURICAM Network Camera

Бренд: D-Link Страницы: 68

DCS-1110 - Network Camera

Бренд: D-Link Страницы: 16

Бренд: DBI SALA Страницы: 120

Бренд: LaserLine Страницы: 68

Бренд: Hanwha Vision Страницы: 20

Бренд: La Crosse Страницы: 3

Бренд: Banner Страницы: 76

Бренд: MAXIMUM Security Страницы: 40

Бренд: Tamron Страницы: 3

Бренд: Maxocam Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды