Bosch DLN54AA70A, Руководство пользователя и инструкции по установке

Страница: 12 / 16

en
Installation instructions
12
Sharp-edged components inside the appliance may
damage the connecting cable.
▶
Do not kink or trap the connecting cable.
¡
The connection data can be found on the rating
plate. → Page 9
¡
The connecting cable is approx. 1.30 m long.
¡
This appliance complies with the EC interference
suppression regulations.
¡
The appliance corresponds to protection class 1.
You should therefore only use the appliance with a
protective earth connection.
¡
Do not connect the appliance to the power supply
during installation.
¡
Ensure that the protection against contact is guaran-
teed during installation.
12.7 Information on the installation situation
¡
Install this appliance in a kitchen cupboard.
¡
To install additional special accessory parts, ob-
serve the enclosed installation instructions.
¡
The width of the extractor hood must correspond at
least with the width of the hob.
¡
To optimally detect the cooking vapours, install the
appliance in the middle of the hob.
12.8 Instructions for the exhaust air pipe
The appliance manufacturer does not provide any war-
ranty for faults attributable to the pipeline.
¡
Use a short, straight exhaust air pipe with as large a
pipe diameter as possible.
¡
Long, rough exhaust air pipes, many pipe bends or
small pipe diameters reduce the suction power and
increase the fan noise.
¡
Use an exhaust pipe that is made of non-combust-
ible material.
¡
To prevent condensate from returning, fit the ex-
haust pipe with a 1° gradient from the appliance.
Round pipes
Round pipes with an inner diameter of 120 mm.
Flat ducts
Use flat ducts with an inner cross-section that corres-
ponds to the diameter of the round pipes:
¡
Diameter of 120 mm corresponds to ap-
prox. 113 cm².
¡
Use sealing strips for different pipe diameters.
¡
Do not use any flat ducts with sharp bends.
12.9 Instructions for the air extraction mode
For air extraction mode, a one-way flap should be in-
stalled.
Notes
¡
If a one-way flap is not included with the appliance,
one can be ordered from a specialist retailer.
¡
If the exhaust air is conveyed through the external
wall, a telescopic duct should be used.
12.10 Information about circulating-air
mode
The appliance must only be operated when it is se-
curely installed and the pipework is connected.
12.11 Information on combining with a gas
hob
The appliance can be used in conjunction with a gas
hob.
WARNING ‒ Risk of fire!
Operating multiple gas hotplates at the same time gen-
erates a great deal of heat. A ventilation appliance in-
stalled above the cooker may become damaged or
catch fire.
▶
Only operate gas hotplates with cookware on them.
▶
Select the highest fan setting.
▶
The appliance must only be combined with gas hot-
plates with a total output of the following values:
- Maximum total power: 9.75 kW
- Power for a single gas hotplate: 4 kW
- Maximum total power of the rear hotplates:
5.25 kW
When installing with a gas hob, we recommend using a
gas hob from the Bosch brand.
12.12 Installation
Checking the unit
1. Check whether the fitted unit is level and has suffi-
cient load-bearing capacity.
The max. weight of the appliance is 5 kg.
Note: Note the furniture manufacturer's specifica-
tions with regard to the load-bearing capacity of the
fitted unit.
2. Ensure that the fitted unit is heat-resistant up to
90 °C.
3. Ensure that the fitted unit is still stable after the cut-
outs have been made.
Preparing the units
Requirement:
The unit is suitable for the installation.
→ "Checking the unit", Page 12