en
Installation instructions
12
▶
▶
Repairs to the appliance should only
be carried out by trained specialist
staff.
¡
Incorrect repairs are dangerous.
▶
Repairs to the appliance should only
be carried out by trained specialist
staff.
▶
Only use genuine spare parts when re-
pairing the appliance.
▶
If the power cord of this appliance is
damaged, it must be replaced by the
manufacturer, the manufacturer's Cus-
tomer Service or a similarly qualified
person in order to prevent any risk.
¡
Improper installation is dangerous.
▶
Connect and operate the appliance
only in accordance with the specifica-
tions on the rating plate.
▶
Connect the appliance to a power sup-
ply with alternating current only via a
properly installed socket with earthing.
▶
The protective conductor system of the
domestic electrical installation must be
properly installed.
▶
Never equip the appliance with an ex-
ternal switching device, e.g. a timer or
remote control.
▶
When the appliance is installed, the
mains plug of the power cord must be
freely accessible. If free access is not
possible, an all-pole isolating switch
must be installed in the permanent
electrical installation according to the
conditions of Overvoltage Category III
and according to the installation regula-
tions.
▶
When installing the appliance, check
that the power cable is not trapped or
damaged.
Information on the installation situation
¡
Install this appliance in a kitchen cupboard.
Instructions for the exhaust air pipe
The appliance manufacturer does not provide any war-
ranty for faults attributable to the pipeline.
¡
Use a short, straight exhaust air pipe with as large a
pipe diameter as possible.
¡
Long, rough exhaust air pipes, many pipe bends or
small pipe diameters reduce the suction power and
increase the fan noise.
¡
An exhaust air pipe that is made of non-combustible
material.
¡
To prevent condensate from returning, fit the ex-
haust air pipe from the appliance with a 1° gradient.
Round pipes
Use round pipes with an inner diameter of 150 mm (re-
commended) or at least 120 mm.
Flat ducts
Use flat ducts with an inner cross-section that corres-
ponds to the diameter of the round pipes:
¡
Diameter of 150 mm corresponds to ap-
prox. 177 cm².
¡
Diameter of 120 mm corresponds to ap-
prox. 113 cm².
¡
Use sealing strips for different pipe diameters.
¡
Do not use any flat ducts with sharp bends.
Instructions for the electrical connection
In order to be able to safely connect the appliance to
the electrical system, follow these instructions.
WARNING ‒ Risk of electric shock!
¡
It must always be possible to disconnect the appli-
ance from the electricity supply. The appliance must
only be connected to a protective contact socket
that has been correctly installed.
▶
The mains plug for the mains power cable must
be easily accessible after the appliance is in-
stalled.
▶
If this is not possible, an all-pole isolating switch
must be integrated into the permanent electrical
installation according to the conditions of over-
voltage category III and according to the installa-
tion regulations.
▶
The permanent electrical installation must only
be wired by a professional electrician. We recom-
mend installing a residual-current circuit breaker
(RCCB) in the appliance's power supply circuit.
¡
Sharp-edged components inside the appliance may
damage the connecting cable.
▶
Do not kink or trap the connecting cable.
¡
The connection data can be found on the rating
plate inside the appliance.
¡
To see the rating plate, remove the grease filter.
¡
The connecting cable is approx. 1.30 m long.
¡
This appliance complies with the EC interference
suppression regulations.
¡
The appliance corresponds to protection class 1.
Therefore, only use the appliance with a protective
earth connection.
¡
Do not connect the appliance to the power supply
during installation.
¡
Ensure that the protection against contact is guaran-
teed during installation.
General information
Follow these general instructions during the installation.
¡
For the installation, observe the currently valid build-
ing regulations and the regulations of the local elec-
tricity and gas suppliers.
¡
When discharging the exhaust air, the official and
legal regulations, such as the regional building
code., must be observed.
¡
The width of the extractor hood must correspond at
least with the width of the hob.
