Bosch BSG8PRO Series, Инструкция по эксплуатации

Страница: 12 / 142

11
When the work is done
Figure
䡲
Switch the vacuum cleaner off and unplug the power
cord from the mains.
䡲
Tug the power cord and let go. The cable then rewinds
automatically.
䡲
To reactivate or deactivate the cable brake, quickly tug
the power cord.
Figure
To store or transport the vacuum cleaner, use the storage
aid on the underside of the vacuum cleaner. Stand the
vacuum cleaner up on its end. Slide the plastic lug on the
floor tool into the groove on the underside of the unit.
Changing the dust bag and filters
Replacing the dust bag
Figure
䡲
If the dust bag change indicator lights up brightly and
evenly when the floor tool is lifted from the carpet and
the highest suction power is selected, the dust bag must
be changed, even though it may not yet be full. In this
case it is essential to change the dust bag due to the
type of material it contains.
䡲
Open the dust bag compartment lid by moving the dust
compartment locking lever in the direction of the arrow.
Figure
Seal the dust bag by pulling the self-seal tap and then
remove it.
Figure
Insert a new dust bag into the holder and close the dust
bag compartment lid.
!
Caution: the dust bag compartment lid will only close
when the disposable or textile filter are inserted.
If the dust bag change indicator is still lit after the
dust bag has been changed, please check whether
the nozzle, tube or flexible hose are blocked.
Cleaning the motor protection filter
The motor protection filter should be cleaned regularly by
knocking out the dirt and rinsing.
Figure
䡲
Open the dust bag compartment lid (see Figure 14).
䡲
Pull out the motor protection filter in the direction of the
arrow.
䡲
Clean the motor protection filter by tapping it.
䡲
If it is very dirty, the motor protection filter should be
rinsed.
The filter must then be left to dry for at least 24 hours.
䡲
After cleaning, insert the motor protection filter into the
appliance as far as it will go and close the dust bag
compartment lid.
17
16
15
14
13
12
Caution!
Floor tools are subject to a certain amount of wear,
depending on the type of hard floors you have
(e.g. rough, rustic tiles). Therefore, you must check
the underside of the floor tool at regular intervals.
Worn undersides of floor tools may have sharp edges
that can damage sensitive hard floors, such as parquet
or linoleum. The manufacturer does not accept any
responsibility for damage caused by worn floor tools.
Turbo brush
If your vacuum cleaner is equipped with a turbo brush,
please consult the accompanying instruction manual for
notes on its use and maintenance.
Vacuuming with accessories
Figure
Remove the accessory from the case and attach to the
handle or suction pipe.
a) Professional crevice nozzle
Extra long crevice nozzle for cleaning crevices, corners
and narrow spaces, e.g. in a car.
b) Professional furniture brush
For large-surface vacuuming of furniture requiring
particular care, picture frames, books, etc.
c) Professional upholstery nozzle
䡲
For gently and thoroughly cleaning upholstered furniture,
curtains, etc.
䡲
To clean the professional upholstery nozzle, simply
vacuum using the handle.
䡲
If it is very dirty, the professional upholstery nozzle can
also be opened.
To do this, turn the two screws on the sides of the nozzle
(e.g. using a coin) and remove the inner part from the
nozzle. After cleaning, replace the inner part (make sure
it is correctly seated) and screw to the housing.
After use, the professional accessories can again be
conveniently stowed in the accessories case.
Figure
Hard-floor brush
For vacuuming hard floor coverings (tiles, parquet floor-
ing, etc.)
Push the telescopic tube into the connecting piece of
the hard-floor brush until it engages.
Press on the unlatching sleeve and pull out the telescop-
ic tube to disconnect.
Figure
You can use the parking aid on the back of the vacuum
cleaner if you wish to stop vacuuming for a short time.
Slide the plastic lug on the tool connector into the
groove at the back of the vacuum cleaner.
11
10*
9
en
*Dependent on model