Bosch BMS500-AAM018-1CSXHC Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 32

background image

|

17

Installation Instructions

Bosch Climate 5000 Series Wall Mounted Ductless Split Air Conditioner / Heat Pump (06.2022)

6 Outdoor Unit Installation

NOTICE



Below information only applies to the single zone
application. For the instructions for the Multi ODU
installation, please refer to the installation manual in the
Multi-zone ODU package.

Step 1: Select installation location

NOTICE



If the unit is frequently exposed to heavy rain or snow:

—

Build a shelter above the unit it to protect it from the
rain or snow. Be careful not to obstruct air flow around
the unit.



This unit is not designed for application in areas frequently
exposed to salty air (seaside) conditions..

Before installing the outdoor unit, you must choose an appropriate location. The
following are standards that will help you choose an appropriate location for the
unit.



Proper installation locations meet the following standards:

—

Meets all spatial minimum requirements shown in Installation Space
Requirements ( Figure 17)

Figure 19

e

v

o

b

a )

ni

4

2(

mc

0

6

60cm (24in)

on right

30cm (12in)

on le

ft

200cm

(79in)

in front

30cm (12in)

from b

ack wall

—

Good air circulation and ventilation

—

Firm and solid—the location can support the unit and will not vibrate

—

Noise from the unit will not disturb others

—

Protected from prolonged periods of direct sunlight or rain



DO NOT install unit in the following locations:

—

Near an obstacle that will block air inlets and outlets

—

Near a public street, crowded areas, or where noise from the unit
will disturb others

—

Near animals or plants that will be harmed by hot air discharge

—

Near any source of combustible gas

—

In a location that is exposed to large amounts of dust

—

In a location exposed to excessive amounts of salty air

NOTICE



If the unit is exposed to heavy wind: Install unit so that air
outlet fan is at a 90° angle to the direction of the wind. If
needed, build a barrier in front of the unit to protect it from
extremely heavy winds. See Figures 18 and 19.

Figure 20

Strong wind

Strong wind

Figure 21

Strong
wind

Wind Baffle

«
...
15
16
17
18
19
...
»

Содержание BMS500-AAM018-1CSXHC

































Отзывы:

Нет отзывов

Похожие инструкции для BMS500-AAM018-1CSXHC

Бренд: Galletti Страницы: 20

Бренд: Panasonic Страницы: 76

Бренд: Panasonic Страницы: 118

Бренд: Haier Страницы: 14

Бренд: Haier Страницы: 20

Бренд: Haier Страницы: 20

Бренд: Haier Страницы: 12

Бренд: Haier Страницы: 36

Бренд: Haier Страницы: 100

Бренд: Haier Страницы: 24

Бренд: Haier Страницы: 19

Бренд: Haier Страницы: 99

ESA3156 - ANNEXE 221

Бренд: Haier Страницы: 25

Бренд: Haier Страницы: 26

Бренд: Haier Страницы: 25

Бренд: Haier Страницы: 19

Бренд: Haier Страницы: 25

ESA3067 - annexe 1

Бренд: Haier Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды