Bosch AQT 33-11, Оригинальное руководство пользователя, Страница: 15 / 264

English | 15
Bosch Power Tools F 016 L81 709 | (11.4.17)
Noise/Vibration Information
Sound emission values determined according to
EN 60335-2-79.
Typically the A-weighted noise levels of the product are:
Sound pressure level 85 dB(A); sound power level 94 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a
h
(triax vector sum) and uncertainty K
determined according to EN 60335-2-79:
a
h
=4 m/s
2
, K=1.5 m/s
2
.
Mounting and Operation
Starting
Electrical Safety
Warning! Switch off, remove plug from mains
before adjusting, cleaning or if cable is cut,
damaged or entangled.
Your machine is double insulated for safety and requires no
earth connection. The operating voltage is 230 V AC, 50 Hz
(for non-EU countries 220 V, 240 V as applicable).
For increased electrical safety use a Residual Current Device
(RCD) with a tripping current of not more than 30 mA. Always
check your RCD every time you use it.
The supply cables must be inspected for signs of damage at
regular intervals and may only be used if in perfect condition.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
Only use approved extension cables.
WARNING! Inadequate extension cables can
be dangerous. Extension cable, plug and sock-
et must be of watertight construction and in-
tended for outdoor use.
Extension cords, cables, leads, reels should only be used if
they comply with EN 61242/IEC 61242 or
IEC 60884-2-7.
If you want to use an extension cable when operating your
product, only the following cable dimensions should be used:
– Nominal Conductor Area of 1.5mm
2
to a max. cable length
of 20m for a Cord Extension Set
The connections (plugs and sockets) should be kept dry and
off the ground.
It is recommended that this is accomplished by means of a
cord reel which keeps the socket at least 60 mm above the
ground.
Note: If an extension cable is used it must be earthed and con-
nected through the plug to the earth cable of your supply net-
work in accordance with prescribed safety regulations.
Refer to the instruction manual of the extension cord, lead,
reel manufacturer and your local wiring regulations.
If in doubt contact a qualified electrician or the nearest Bosch
Service Centre.
For products not sold in GB :
WARNING: For your safety, it is required that the plug at-
tached to the product is connected with the extension cord.
The coupling of the extension cord must be protected against
splash water, be made of rubber or coated with rubber. The
extension cord must be used with a cable strain relief.

Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse
(ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug fitted in its place by an
authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
Rated pressure MPa 7.4
Rated Flow l/min 4.7
Maximum inlet pressure MPa 1
Autostop function

Weight according to EPTA-
Procedure 01:2014
kg 4.5
Protection class /
II
Serial number See serial number
(rating plate) on
pressure washer.
Action Figure Page
Delivery Scope 1 253
Mounting cable bracket/in use storage for
gun
2 253
Connecting/disconnecting high pressure
gun to lance
3 254
Connecting/disconnecting nozzle 3 254
Connecting/disconnecting high pressure
water supply hose/nozzle
4 255
Connecting to the water supply 5 255
Switching On and Off 6 256
Adjust water jet 7 256
Connect detergent bottle 8 257
Clean nozzle 9 257
Clean the water filter 10 258
Transport 11 258
Storage 11 259
Selecting Accessories 12 260
Pressure washer AQT 33-11
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Starting cycles generate brief voltage drops. Interference with other
equipment/machines may occur in case of unfavourable mains system
conditions. Malfunctions are not to be expected for system impedances
below 0.153 ohm.
OBJ_DOKU-44047-004.fm Page 15 Tuesday, April 11, 2017 9:17 AM