background image

F 002 DG9 432

2014-12-19

Bosch Limited

Troubleshooting  |  ACS 255  |  13

en

5. 

Troubleshooting

Error code

Messages

Actions

1001

RECOVERY - Service Timeout

Check for blockage in the vehicle A/C system.

1004

RECOVERY - Internal Tank full

 

R

Weight limit reached. Reduce quantity of refrigerant in refrigerant tank.

 

R

Load cell is defective. Contact customer service.

100A

RECOVERY - Low pressure in A/C

 

R

Ensure quick couplers are connected properly to the service ports on the vehi-

cle A/C system.

 

R

If the couplers are connected properly, try to perform A/C service. If the error 

persists, contact customer service.

2001

VACUUMING - Perform Recovery

The pressure is greater than 1400 mbar while vacuuming:

 

R

Continue the recovery.

 

R

Abort the recovery.

2002

VACUUMING - Leak Detected

Repair the vehicle A/C system.

5001

R134A RECHARGE - Service  

Timeout

 

R

Check for blockage in the ACS 255.

 

R

Check if quick couplers are open.

5002

R134A RECHARGE - Insufficient 

R134a

Fill the internal refrigerant tank.

5005

R134A RECHARGE - Internal Tank 

full

 

R

Weight limit reached. Reduce quantity of refrigerant in internal refrigerant tank.

 

R

Load cell is defective. Contact customer service.

5006

R134A RECHARGE - Perform  

Recovery

 

R

Continue the recovery.

 

R

Abort the recovery.

5007

R134A RECHARGE - Perform  

Vacuuming

Perform vacuuming.

7100

Safety Switch - SS shutdown

 

R

Allow the unit to cool for 30 minutes and switch on the ACS 255. Try recovery/

hose drain.

 

R

Check if the blue knob on the refrigerant tank is closed. Open the blue knob If 

it is closed.

 

R

Contact customer service if the problem persists.

7302

PS - Sensor failure

 

R

Contact customer service.

 

R

For error messages 7501, 7502, 7503, 8000 and C001, contact customer ser-

vice

9102

FACTORY SETTING - Not  

Complete

 

R

Self-test failed. See the self test report and take corrective action.

A101

TANK FILL - Service Timeout

Check for blockage in the ACS 255.

ACS 255..

A103

TANK FILL - Internal Tank full

 

R

Weight limit reached. Reduce quantity of refrigerant in refrigerant tank.

 

R

Load cell is defective. Contact customer service.

A105

TANK FILL - Check Ext. valve

 

R

Check if the valve on the external tank is open.

 

R

Check if R134a is available in the external tank.

A601

R134a TOP UP - Service Timeout

 

R

Check if the vehicle A/C system is on.

 

R

Check for blockage in the ACS 255.

 

R

Check the refrigerant tank scale.

 

R

Check for blockage in the hoses

A602

R134a TOP UP - Insufficient 

R134a Quantity

 

R

Check if the vehicle A/C system is on.

 

R

Check for blockage in the ACS 255.

C002

OIL RECHARGE - Perform Recovery The pressure is greater than 1400 mbar while recharging. Perform recovery.

C003

OIL RECHARGE - Perform  

Vacuuming

The pressure is greater than 900 mbar while recharging. Perform vacuuming.

C005

OIL RECHARGE - AC high  

pressure

 

R

Check if the fresh oil bottle is connected

 

R

Contact customer service

D003

PERFORMANCE TEST - Perform 

Hose drain

The pressure is greater than 1400 mbar. Perform hose drain.

 

i

The message "Service Timeout" indicates the service timeout for any service phase which is in progress. The 
following table indicates the service timeout duration for different service phases.

Service phase

Timeout duration (mins)

Refrigerant recovery

120

Recharge oil

6

Service phase

Timeout duration (mins)

Recharge refrigerant

15

Hose drain

5

Содержание ACS 255

























Отзывы: