Bosch 9-115 S GWS Professional, Оригинальное руководство пользователя

Страница: 20 / 265

20 | English
The regulations on the material being machined that apply in
the country of use must be observed.
u
Avoid dust accumulation at the workplace. Dust can
easily ignite.
Operation
Start-up
u
Pay attention to the mains voltage. The voltage of the
power source must match the voltage specified on the
rating plate of the power tool. Power tools marked
with 230 V can also be operated with 220 V.
When operating the power tool using a mobile generator that
does not have sufficient reserve capacity or an adequate
voltage control system with inrush current boost converter,
loss of performance or atypical behaviour may occur upon
switch-on.
Please check the suitability of the power generator you are
using, particularly with regard to the mains voltage and fre-
quency.
u
Products that are only sold in AUS and NZ: Use a resid-
ual current device (RCD) with a nominal residual current
of 30 mA or less.
u
Hold the tool by the insulated gripping surfaces and
auxiliary handle only.
The application tool could come
into contact with hidden wiring or its own cord. Con-
tact with live wires may make metal parts of the tool live,
posing a risk of electric shock.
Switching on/off
To start the power tool, first slide the lock-off switch (3)
backwards, then press and hold the on/off switch (2) .
To switch off the power tool, release the on/off switch (2) .
u
Always check abrasive tools before using them. The
abrasive tool must be fitted properly and be able to
move freely. Carry out a test run for at least one
minute with no load. Do not use abrasive tools that are
damaged, run untrue or vibrate during use.
Damaged
abrasive tools can burst apart and cause injuries.
Working advice
u
Pull the plug out of the socket before carrying out any
work on the power tool.
u
Exercise caution when cutting slots in structural walls;
see the "Information on structural design" section.
u
Clamp the workpiece if it is not secure under its own
weight.
u
Do not load the power tool so heavily that it comes to a
stop.
u
If the power tool has been subjected to a heavy load,
continue to run it at no-load for several minutes to
cool down the accessory.
u
Do not use the power tool with a cut-off stand.
u
Do not touch grinding and cutting discs until they have
cooled down.
The discs can become very hot while work-
ing.
Rough grinding
u
Never use cutting discs for rough grinding.
The best rough grinding results are achieved with a set angle
of 30° to 40°. Move the power tool back and forth with mod-
erate pressure. This will ensure that the workpiece does not
become too hot or discolour and that grooves are not
formed.
Flap Disc
With the flap disc (accessory), curved surfaces and profiles
can be worked. Flap discs have a considerably higher ser-
vice life, lower noise levels and lower sanding temperatures
than conventional sanding sheets.
Cutting Metal
u
Always use the protective guard for cutting (12) when
cutting bonded abrasives.
When carrying out abrasive cutting, use a moderate feed
that is suited to the material being machined. Do not exert
pressure on the cutting disc and do not tilt or swing the
power tool.
Do not attempt to reduce the speed of a cutting disc coming
to a stop by applying pressure from the side.
The power tool must always
work in an up-grinding mo-
tion. Otherwise, there is a
risk that it will be pushed
uncontrolled out of the cut.
For best results when cut-
ting profiles and rectangular
tubing, start at the smallest
cross section.
Cutting Stone
u
Provide sufficient dust extraction when cutting stone.
u
Wear a dust mask.
u
The power tool may be used only for dry cutting/grind-
ing.
For cutting stone, it is best to use a diamond cutting disc.
When cutting especially hard materials such as concrete
with a high pebble content, the diamond cutting disc can
overheat and become damaged as a result. This is clearly in-
dicated by circular sparking, rotating with the diamond cut-
ting disc.
If this happens, stop cutting and allow the diamond cutting
disc to cool down by running the power tool for a short time
at maximum speed with no load.
If work is noticeably slower and circular sparking is present,
this indicates that the diamond cutting disc has become
blunt. You can resharpen the disc by briefly cutting into ab-
rasive material (e.g. lime-sand brick).
1 609 92A 5FP | (24.04.2020) Bosch Power Tools