38
| English
Changing the saw blade (see figures k1−k4)
u
Pull the plug out of the socket before carrying out any
work on the power tool.
u
When mounting the saw blade, wear protective
gloves.
This poses a risk of injury.
u
Only use saw blades the maximum permitted speed of
which is higher than the no-load speed of the power
tool.
u
Only use saw blades that match the specifications
given in this operating manual and that are tested and
marked in accordance with EN 847-1
u
Only use saw blades that are recommended by the
power tool manufacturer and are suitable for use on
the material you want to saw.
This prevents the saw
tooth tips from overheating and the plastic you want to
saw from melting.
u
Do not use HSS saw blades.
Such saw blades can easily
break.
Removing the saw blade
– Turn the crank
(18)
clockwise as far as possible so that
the saw blade
(26)
is in the highest possible position
above the saw table.
– Open the clamping lever
(37)
and pull the protective
cover
(6)
out of the groove on the riving knife
(7)
.
– Use a screwdriver to lift the table insert
(25)
at the front
and remove it from the tool chamber.
– Turn the clamping nut
(46)
using the ring spanner
(22)
while pulling the spindle locking lever
(47)
until it en-
gages.
– Keep pulling the spindle locking lever and unscrew the
clamping nut anti-clockwise.
– Remove the clamping flange
(48)
.
– Remove the saw blade
(26)
.
Fitting the saw blade
If required, clean all the parts you want to fit before installing
them.
– Place the new saw blade on the mounting flange
(50)
of
the tool spindle
(49)
.
Note:
Use sufficiently large saw blades. The radial clearance
between the saw blade and the riving knife must not exceed
3−8 mm (max.).
u
When mounting the saw blade, ensure that the cutting
direction of the teeth (direction of the arrow on the
saw blade) matches the direction of the arrow on the
riving knife.
– Fit the clamping flange
(48)
and the clamping nut
(46)
.
– Turn the clamping nut
(46)
using the ring spanner
(22)
while pulling the spindle locking lever
(47)
until it en-
gages.
– Tighten the clamping nut by turning it clockwise.
– Reinsert the table insert
(25)
.
– Refit the protective cover
(6)
.
Operation
u
Pull the plug out of the socket before carrying out any
work on the power tool.
Transport position and work position of the saw
blade
Transport position
– Remove the protective cover
(6)
, remove the table insert
(25)
and place the riving knife
(7)
in the bottom position.
Reinsert the table insert
(25)
.
– Turn the crank
(18)
anticlockwise until the teeth of the
saw blade
(26)
lie below the saw table
(8)
.
– Push the saw table expansion
(13)
in fully.
Push the clamping handle
(15)
down. This fixes the saw
table expansion in place.
Work position
– Position the riving knife
(7)
in the top position directly
over the centre of the saw blade, insert the table insert
(25)
and fit the protective cover
(6)
.
– Turn the crank
(18)
clockwise until the top teeth of the
saw blade
(26)
are approx. 3−6 mm above the work-
piece.
Setting mitre and bevel angles
To ensure precise cuts, the basic settings of the power tool
must be checked and adjusted as necessary after intensive
use.
Setting Bevel Angles (saw blade) (see figure A)
The bevel angle can be set between
-2°
and
47°
.
– Loosen the locking lever
(16)
by turning it anticlockwise.
Note:
When the locking lever is fully loosened, gravity
causes the saw blade to tilt into a position that corresponds
to approximately 30°.
– Pull or push the hand wheel
(17)
along the slotted link un-
til the angle indicator
(51)
shows the required bevel
angle.
– Hold the hand wheel in this position and retighten the
locking lever
(16)
.
For quick and precise setting of the standard bevel
angles of 0° and 45°
, there are pre-set stops (
(59)
),(
(62)
).
Setting mitre angles (angle guide) (see figure B)
The mitre angle can be set between
60°
(left-hand side) and
60°
(right-hand side).
– Loosen the locking knob
(53)
if it is tightened.
– Turn the angle guide until the angle indicator
(54)
shows
the required mitre angle.
– Retighten the locking knob
(53)
.
Extending the saw table
The free end of long and heavy workpieces must have some-
thing placed underneath it or be supported.
1 609 92A 7NM | (27.04.2022)
Bosch Power Tools
Содержание 3 601 M30 502
