12
| English
Battery Charging (Accessory)
Note:
The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the Electronic Cell Protection (ECP). A protective circuit
switches the cordless worklight off when the battery is
drained.
u
Do not continue to press the On/Off switch after the
worklight has been automatically switched off.
The
battery can be damaged. Ensure that the battery is
charged and that the worklight has cooled before switch-
ing on the worklight again.
To remove the battery
(8)
, press the release button
(10)
and pull the battery out of the cordless worklight.
Do not use
force to do this.
Follow the instructions on correct disposal.
Operation
Starting Operation
Inserting the battery (see figure A)
Push the charged battery
(8)
into the battery holder
(14)
until it clicks into place.
Setting up
Place the cordless worklight on a stable, level surface. Make
sure it is secure.
The safety brackets
(3)
protect the light
(1)
from damage,
should the cordless worklight be accidentally knocked over.
Fastening to the Tripod
You can use the tripod mount
(9)
to screw the cordless
worklight onto a tripod.
Attach the cordless worklight firmly to the tripod. Ensure the
cordless worklight cannot come loose and/or fall over.
Ensure that the tripod has a firm footing.
Switching on/off and adjusting the brightness
On/off switch
Function
Press once
Switches on the cordless worklight,
dimmed (level 1)
Press twice
Switches on the cordless worklight,
dimmed (level 2)
Press three times
Switches on the cordless worklight,
full brightness (level 3)
Press four times
Switches off the cordless worklight
If the cordless worklight has been switched on for approx.
five minutes, it will be switched off immediately the next
time the button is pressed.
Temperature Dependent Overload Protection
If the permissible operating temperature is exceeded, the
cordless worklight switches off. Let the cordless worklight
cool down and then switch the cordless worklight back on.
Battery Charge Indicator (Cordless Worklight)
When the cordless worklight is switched on, the five LEDs of
the battery charge indicator
(6)
display the state of charge
of the battery
(8)
.
Battery charge indicator
The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For reasons of safety, it is only
possible to query the state of charge when the cordless
worklight is switched off.
Press the button for the battery charge indicator or
to
show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.
Battery model GBA 18V...
LEDs
Capacity
3× continuous green light
60−100 %
2× continuous green light
30−60 %
1× continuous green light
5−30 %
1× flashing green light
0−5 %
Battery model ProCORE18V...
LEDs
Capacity
5× continuous green light
80−100 %
4× continuous green light
60−80 %
3× continuous green light
40−60 %
2× continuous green light
20−40 %
1× continuous green light
5−20 %
1× flashing green light
0−5 %
Changing the button cell (see figure A)
A warning will be displayed in the app before the button cell
is fully used up.
To open the battery compartment cover
(11)
, turn it anti-
clockwise with a screwdriver and then lift off the battery
compartment cover. Remove the empty button cell and in-
sert a new button cell.
Make sure that the battery holder is
not damaged when removing the cell. Make sure that the
positive pole of the button cell faces upwards.
Close the battery compartment cover back up.
1 609 92A 4U8 | (03.09.2019)
Bosch Power Tools
