Bort 91271082, Руководство пользователя

Страница: 6 / 24

6
Car compressor
Intended Use
This product is used for inflation of tires, balls, inflatable
air beds, bicycle tires, etc. The car compressor is equipped
with a manometer and an adaptor for connection to the
car cigarette lighter.
Technical specifications
Car system voltage, V 12
Power, W 60
Discharge, litres per min. 12
Idling speed, rpm 1500
Maximum output pressure,
bar (Pa)
7 (700000)
Weight, kg 0,8
GENERAL REQUIREMENTS
• Do not leave the car compressor in the rain and snow.
• Do not use the product in highly humid environment.
• Do not work near inflammable liquids and gases.
• Do not let children operate the car compressor.
• Keep in a dry and closed place out of reach of children.
• Do not overload the product. Failures caused by over-
load are not covered by conditions of free warranty
repair.
• Use only for the purpose specified.
• Control operability of the air hose.
• It is prohibited to move the compressor holding it by the
power cable.
• Avoid contact of the hose with oil and sharp objects.
• Avoid overheating of the hose.
• Keep your balance while working.
• Keep the compressor clean. Clean it regularly from oil
stains.
• Disconnect the compressor from the car system voltage
in the following cases:
- The product is not in use.
- During maintenance operations.
- During replacement of parts and mechanical units.
• Be attentive and collected while working.
• Refrain from work, if you are tired or ill.
• Regularly check the product for damages and failures.
• If any defects are detected, contact the service center
• For failure avoidance, do not use spare parts of other
manufacturers.
To prevent failures
• Keep the compressor adapter clean. With the compres-
sor connected to the car cigarette lighter, in case of
short circuit, a life-threatening situation may occur. Ac-
cumulator capacity is very high, so you can get injured.
• Protect the compressor from overheating. Do not cover
the compressor with foreign objects while in use.
Before connecting, please check
• If the adapter and the car lighter socket match;
• If the car accumulator voltage matches with the com-
pressor’s characteristics;
• If the accumulator can provide 10 A;
• Absence of failures and breakdowns in the cable and the
adapter for the cigarette lighter.
OPERATION
• First, check pressure in the inflated object. It can be
done with the manometer, installed in the compressor.
Just connect the hose of the idle compressor to the
inflated object.
• Avoid excessive pressurization.
• Do not place the working compressor in the car com-
partment.
• Do not leave the working compressor unattended.
• Switch off the compressor immediately in the following
cases:
1. If the adapter or power cable is damaged;
2. Smell of burning insulation appears.
ATTENTION! This compressor is intended for short-time
operation (not more than 10 minutes). Longer operation
of the compressor may cause its overheating and break-
down. If you need to use the compressor longer, after first
10 minutes switch off the device and let it cool down for
10 minutes before restart.
Inflation of car tires
• Place the car to ensure the lowest position of the tire
valve.
• Connect the nipple to the tire valve. Push the lever
down and fix the nipple.
• Check pressure with the manometer.
• Connect the compressor to the car lighter socket.
• When the required pressure level is reached, disconnect
the compressor from the car lighter socket.
• Release the lock of the joining nipple and remove it
from the valve.
Inflation of balls and toys
• Install the valve adapter (connector or needle for ball
inflation) on the nipple and latch the lock by pushing
the lever down.
• Connect the air hose with the adapter to the inflated
object.
• Connect the compressor to the car lighter socket.
• Turn the compressor on.
• When the required pressure level is reached, disconnect
the compressor from the car lighter socket.
• Disconnect the air hose with the adapter from the in-
flated object.
• Quickly close the air passage of the inflated object.
ATTENTION! Control air pressure in the inflated object.
Avoid excessive pressurization of the inflated object.
English