BorMann 030577, Руководство пользователя

Страница: 4 / 10

EN
WWW.BORMANNTOOLS.COM
4
• Wear personal protective equipment. Depending on application , use face shield, safety goggles or safety glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of stopping small abrasive or workpiece fragments. The eye protection must be capable of stopping flying
debris generated by various operations. The dust mask or respirator must be capable of filtrating particles generated by your operation. Prolonged exposure
to high intensity noise may cause hearing loss.
• Keep bystanders a safe distance away from work area. Anyone entering the work area must wear personal protective equipment. Fragments of workpiece or
of a broken accessory may fly away and cause injury beyond immediate area of operation.
• Hold the power tool by insulated gripping surfaces only, when performing an operation whe re the cutting accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock.
• Position the cord clear of the spinning accessory . If you lose control, the cord may be cut or snagged and your hand or arm may be pulled into the spinning
accessory.
• Never lay the power tool down until the accessory has come to a complete stop. The spinning accessory may grab the surface and pull the power tool out of
your control.
• Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into
your body.
• Regularly clean the power tool's air vents. The motor's fan will draw the dust inside the housing and excessive accumulation of powdered metal may cause
electrical hazards
• Do not operate the power tool near flammable materials. Sparks could ignite these materials.
• Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in electrocution or shock.
Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any other accessory. Pinching or snagging causes rapid stalling of
the rotating accessory which in turn causes the uncontrolled power tool to be forced in the direction opposite of the accessory's rotation at the point of the
binding.
For example, if an abrasive wheel is snagged or pinched by the workpiece , the edge of the wheel that is entering into the pinch point can dig into the surface
of the material causing the wheel to climb out or kick out. The wheel may either jump toward or away from the operator, depending on direction of the wheel's
movement at the point of pinching. Abrasive wheels may also break under these conditions. Kickback is the result of power tool misuse and/or incorrect oper-
ating procedures or conditions and can be avoided by taking proper precautions as given below.
• Maintain a firm grip on the power tool and position your body and arm to allow you to resist kickback forces. Always use auxiliary handle, if provided, for max-
imum control over kickback or torque reaction during start-up. The operator can control torque reactions or kickback forces, if proper precautions are taken.
• Never place your hand near the rotating accessory. Accessory may kickback over your hand.
• Do not position your body in the area where power tool will move if kickback occurs. Kickback will propel the tool in direction opposite to the wheel's move-
ment at the point of snagging.
• Use special care when working corners, sharp edges etc. Avoid bouncing and snagging the accessory. Corners , sharp edges or bouncing have a tendency
to snag the rotating accessory and cause loss of control or kickback. Do not attach a saw chain woodcarving blade or toothed saw blade. Such blades create
frequent kickback and loss of control.
Safety Warnings Specific for Polishing Operations
• Do not allow any loose portion of the polishing bonnet or its attachment strings to spin freely . Tuck away or trim any loose attachment strings . Loose and
spinning attachment strings can entangle your fingers or snag on the workpiece.
Additional safety instructions
• The mains voltage and the voltage specifications on the rating plate must correspond .
• Do not press the spindle lock until the tool stops.
Technical Data
Voltage/Frequency 220-240V - 50Hz
Power 1200W
No-load speed
1400
- 4
800
rpm
Tool Max diameter 150 mm
Pitch circle diameter 15 mm
Operating Instructions
WARNING! Before carrying out any work on the polisher, always pull out the mains plug. Before switching on the polisher Unpack the polisher and check that
there are no missing or damaged parts.
Attaching or changing tools (Fig.2)
• Pull out the mains plug.
• Firmly press polishing tool (1), centred on the eye, onto the Velcro pad (2). Use undamaged polishing tools only.
• Insert the mains plug into the socket.
• Switch on the polisher (without engaging it) and run the polisher for approx. 30 sec. Check for imbalances and vibrations.
• Switch off the polisher
Description of main parts
Fig.1
1. Grip
2. Gear head
3. Polishing head screw
4. Velcro pad
5. Switch
6. Locking button locks the switch
7. Dial for preselecting the speed
Fig.2
1. Polishing tool
2. Velcro pad
Fig.3
1. Hexagonal wrench
2. Screw
3. Velcro pad