6
11
2. Whilst another person lifts the back of the Frame (1),
attach the Rear Stabiliser (28) to the Frame with two
M8 x 53mm Button Bolts (34), two M8 Washers (48),
and two M8 Nylon Locknuts (38).
34
28
48
48
1
2
38
3. Insert the Console Bracket (63) into the Upright (2) as
shown. Attach the Console Bracket to the Upright with
an M8 x 25mm Button Screw (45), two M8 Split
Washers (59), and two M8 x 19mm Button Screws
(68).
4. The Console (23) requires three 1.5V “AA” batteries;
alkaline batteries are recommended. Insert three bat-
teries into the battery compartment.
Make sure that
the batteries are oriented as shown by the diagram
inside the battery compartment.
63
45
59
68
59
68
2
3
5. Have another person hold the Console (23) in the
position shown. Insert the control cable down through
the Upright (2). Connect the console wire to the Upper
Wire (44). Attach the ground wire to the Console
Bracket (63) with an M4 x 16mm Screw (42). Next,
insert the excess cable and wire down into the Upright.
Attach the Console (23) to the Console Bracket (63)
with four M4 x 16mm Screws (42).
Be careful to
avoid pinching the cable and wires.
Make sure that the resistance knob is turned to the
lowest setting before continuing.
4
23
23
5
Batteries
63
42
2
42
Control Cable
Resistance
Knob
Console Wire
Ground
Wire
44
HOW TO USE A PACE PROGRAM
Turn on the console.
See step 1 on page 10.
Select one of the four pace programs.
Each time the
console is
turned on, the
manual mode
will be selected.
To select a
pace program,
press the
Program button
repeatedly until the number 1, 2, 3, or 4 appears
in the upper right corner of the display.
The four profiles on the right side of the console
show how the target pace will change during the
programs. For example, profile number 1 shows
that during program 1, the target pace will
increase near the beginning of the program, and
then decrease near the end.
Start the program.
To start the program, begin pedalling. Each pro-
gram consists of either 20 or 30 one-minute peri-
ods. One target pace is programmed for each
period. Note: The same target pace setting may
be programmed for two or more consecutive peri-
ods.
The target pace
settings for the
program will be
shown by the
target pace
indicator in the
display. (The
pace indicator
will show your
actual pedalling
pace.) As the
target pace indicator changes in height during the
program, adjust your pedalling pace so that both
indicators are at the same height. If your ped-
alling pace is slower than the current target pace
setting, an arrow will appear next to the pace
indicators to prompt you to increase your pace; if
your pace is faster than the target pace, an arrow
will prompt you to decrease your pace.
Important: The target pace settings for the
program are intended only to provide a goal.
Your actual pace may be slower than the tar-
get pace settings, especially during the first
few months of your exercise program. Make
sure to exercise at a pace that is comfortable
for you.
During the program, adjust the resistance of the
pedals as desired by turning the resistance knob.
The display will show the time remaining in the
program. If you continue exercising after the pro-
gram is completed, the display will continue to
show your exercise feedback.
Follow your progress with the display.
See step 4 on page 10.
Measure your heart rate if desired.
See step 5 on page 10.
When you are finished exercising, the console
will automatically turn off after a few minutes.
See step 6 on page 10.
6
5
4
3
2
1
Pace Indicator
Target Pace Indicator
