BONFIGLIOLI Vectron ACTIVE CUBE Series Скачать руководство пользователя страница 131

Страница: 131 / 200

14.4

Motion control configurations

WARNING

Dangerous state due to new mode!

0x6060

modes of operation

is changed during operation (control word = 0xnnnF), a

dangerous state may occur in the new mode.

•

Before changing

0x6060

modes of operation

, check the status word (e.g. for

state 0xnn33).

Definition Motion Control

For the full function of the Motion Control Interface, you will have to set

Local/Remote

412 = “1-Control via state machine”. In all other operation modes of parameter

Lo-

cal/Remote

412, there are major restrictions. The descriptions in this chapter and of all

objects used are based on the setting

Local/Remote

412 = “1-Control via state ma-

chine”.

Settings

Local/Remote

412 ≠ 1 are described in the “Positioning” application manual.

The function of the state machine describes the basic operating behaviour of the fre-

quency inverter in configurations with position control (

Configuration

30 = x40). The

objects

control word and status word described above support the bits marked as

operation mode specific.

These bits and bit “Target reached” has different meanings in the different position

control operation modes – defined by

0x6060

modes of operation

. The following chap-

ters describe the application of the operation mode specific bits in the

control word

and

status word, depending on the different position control operation modes. Default

value:

0x6060

modes of operation

= 2 – velocity mode.

Basic functions:

The state machine must be set to “operation enabled”, before the position command

can be issued via the operation mode specific bits of the

control word.

Once a

mode of operation has been set by the PLC, no commands will be accepted for

this operation mode until this operation mode is displayed in the

modes of operation

display object.

The bits in the

control word and status word marked as operation mode specific are

only supported in configurations with position control (

Configuration

30 = x40).

07/13

CM-EtherCAT

131

Содержание ACTIVE CUBE Series









































































































































































































Результаты поиска

Содержание ACTIVE CUBE Series

Отзывы:

Похожие инструкции для ACTIVE CUBE Series

Бренды по названию

Популярные бренды

BONFIGLIOLI Vectron ACTIVE CUBE Series, Руководство пользователя

Результаты поиска

Содержание ACTIVE CUBE Series

Отзывы:

Похожие инструкции для ACTIVE CUBE Series

Бренды по названию

Популярные бренды