background image

1-866-771-2663  |  Page 3

damaged part should this occur.
• Do not disconnect any part while unit is in use. 
• Do not store a spare propane tank on or near this unit.
• If the heating unit is indoors, detach the propane tank and leave outdoors. 
• Do not operate on a boat or vehicle. This unit must be used on a flat surface and outdoors ONLY. 
• Always remove protective cover before operating (if applicable).
• Do not set the protective cover over the unit until it is turned off and completely cooled down.
• Check for leaks after not using the unit for long periods of time. 

• Children should never operate this unit. Children must be supervised while near this unit.

• The maximum gas supply pressure is 250psi.

• All installation and repair should be done by a qualified professional. This unit should be 
inspected annually and cleaned regularly.

• Inspect all elements of this heating unit before each use. If there is damage, the burner must be 
replaced.  
• Be aware of the hazards of high temperatures and stay away from the unit to avoid any burns or 
injury. 
• The gas supply tank should be constructed and marked with the specifications for the LP gas tanks 
of the U.S. Department of Transportation or the National Standard of Canada CAN/CSA-B339, LP gas 
tanks, spheres and tubes for Transportation of Dangerous Goods; and Commission. 
• The LP gas tank must have a listed overfilling prevention device and a QCCI or Type I, (CGA810) LP 
gas tank connection.
• This heating appliance should not be used on plastic or artificial wood decks.

• Always follow lighting instructions carefully.
• Do not use 30 lb. propane tanks for this unit.
• In case of high winds, secure this unit to the ground to prevent the unit falling over.

• Children and adults should be alerted to the hazards of high surface temperatures and should 
stay away to avoid burns or clothing ignition.
• Young children should be carefully supervised when they are in the area of the appliance.
• Clothing or other flammable materials should not be hung from the appliance or placed on or 
near the appliance.
• Any guard or other protective device removed for servicing the appliance shall be replaced 
prior to operating the appliance.
• Installation and repair should be done by a qualified service person. The appliance should be 
inspected before use and at least annually by a qualified service person. More frequent cleaning 
may be required as necessary. It is imperative that the control compartment, burners and 
circulating airways of the appliance are kept clean.

•  Keep gas tank at least 152.4 cm / 5 ft. away from unit when lit. (if external tank)

•  Open the door to Inspect the gas hose and all connections to the propane tank prior to each use. If
the hose shows signs of cracking, abrasion, cuts or damage don’t use product and replace the hose
assembly before next use.

Содержание 1500146











































Отзывы: