BONAIRE CRC6910025, Инструкция по эксплуатации

Страница: 4 / 12

Installing
batter
ies
1
2
3
4
Parts and Functions
Indoor Unit
Remote controller
Remove the battery cover;
Install
the batteries
as illustrated.
Be sure that the loading
is in line with th
e" + "/"-";
Load the battery, then replace the cover .
The distance between the signal transmission head and the
receiver hole should be within 7m without any obstructions .
Note:
When
an
electronic-start
er
type fluorescent lamp or change- over
type fluorescent lamp or wireless telephone is installed in the room,
the receiver
may be prone
to
interference
signals, so the distance
to the indoor unit should be kept as short as possible.
D ull display or unclear display during operation indicates the
batteries require replacing .
Replace batteries.
If the remote controller does not respond or responds incorrectly ,
remove the batteries and
re -insert after 5 minutes.
Hint:
Remove the batteries i f unit won't be in use for a long period.
Health function is not available for some units.
1. Mode display
2. Signal sending display
4. FAN SPEED display
5. LOCK display
6. TIMER OFF display
TIMER ON display
7. TEMP display
22. HOUR button
8.
9. TURBO / QUIET button
10. HEAT button
11.
COOL button
12. AUTO button
13.
FAN SPEED button
14. TIMER button
15. HEALTH button
16. LOCK button
Used to lock buttons and LCD display
17.
LIGHT button
18. POWER ON/OFF button
19. DRY button
20. TEMP button
21. SWING button
23. EXTRA FUNCTION button
24. CANCEL/CONFIRM button
Press to s et or cancel the timer or
other functions.
25.
RESET button
When the remote controller appears
abnormal, use a sharp pointed
article to press this button to reset
the remote.
3. SWING display
Operation mode
AUTO FAN COOL DRY
Remote controller
HEAT
LO MED HI
AUTO
Display
circulated
Additional functions display 1
2
3
4
5
9
10
11
12
13
14
15
16
17
8
22
23
24
25
19
20
21
18
7
6
Operation mode
Remote controller
QUIET TURBO SLEEP
Supplemented
electrical
heating
HEALTH
Function: S
LEEP
----
HEALTH
airflow position1---
HEALTH
airflow
position 2 --- Power --- Air sending
--- A-B yard
Display board A
Display board B
Display board C
Display board D
1
4
2
3
1
5
Remote signal receiver
(A beeping sound is generated when a signal from remote controller is
received.)
Power indicator
(Lights up when unit starts.)
Timer mode indicator
(Lights up whenTimer operation is selected.)
Operation mode indicator
(lights up when the compressor is on.)
Ambient temp display
When receiving the remote control signal, display
s
the set temperature
momentarily.
2 3 4 5
2
3
Signal receiver
1
Setting temp.display
2
3
Operation mode indicator
(White light for COOL /
DRY / HEAT mode.
Green light for health function)
1
4
OUTLET
INLET
CONNECTING PIPING
AND ELECTRICAL WIRING
DRAIN HOSE
4
Display board
(adjust left and
ow)
Vertical blade
right air fl
Air Purifying Filter
Inlet
(inside)
Emergency
Switch
Horizontal flap
(adjust up and down air flow
Don't adjust it manually)
Outlet
Inlet grille
Signal receiver hole
COOL display
HEALTH display
4
2
3
1
5
DRY display
6
Ambient temp.display
When receiving the remote
control signal, display s the
set temperature momentarily .
Actual inlet grille may vary from the one shown in the
manual according to the product purchased
2
3
5
6 4
HEAT display
1
(lights up when the compressor is on.)
Ambient temp display
When receiving the remote
control signal, display s the set
temperature momentarily
3
2
4
1
2
3
4
Operation mode indicator
1
TIMER ON/OFF display
TIMER ON OFF display
SLEEP display
Signal receiver hole
Outdoor Unit
Control the lighting on the indoor unit