background image

1

Dear 2004 MX Z X

TM

 440 owner, informations in the 

2004

ZX

TM

 Series REV

TM

 Series Operator’s Guide

 (P/N 520 000

361) also apply to your MX Z X 440 except for the following.

LIMITED WARRANTY VALIDATION

Because of its racing application, the 2004 MX Z X 440 is shipped
from the factory with high compression ratio (CR) combustion cham-
ber inserts installed. 

To validate limited warranty coverage and to run engine with 91 oc-
tane number fuel, the following modifications must be done 

at pre-

delivery before using the vehicle

.

1. Low CR combustion chamber inserts must be installed on engine.

The high CR combustion chamber inserts must be returned to
BOMBARDIER Warranty Department.

2. Replace the main jets with the ones recommended in the 

Prede-

livery bulletin

.

3. Replace the needle jets with the ones recommended in the 

Pre-

delivery bulletin

.

4. Disconnect the pre-heat switch as explained in the 

Predelivery bul-

letin

.

RACING APPLICATION

For racing application, the main jets have to be replaced according to
the chart found on belt guard.

mmo2004_005a.fm  Page 1  Thursday, August 21, 2003  10:43 AM

Содержание Ski-Doo MX Z X 440 2004

















Отзывы: