BOMANN EBK 960 Скачать руководство пользователя страница 6

Страница: 6 / 16

Preparing the worktop for

Preparing the worktop for installation of the hob

installation of the hob

CAUTION:

Before cutting secure the outer cutout
adhesive tape to avoid traces of jigsaw on the
top.

•

The worktop must have a minimum thickness of
30 mm, it must lie horizontally and be sealed to
the wall side against overflowing liquids or moi
ture.

•

The cut surfaces (cutout edges) must be sealed
with special varnish, silicone rubber or cast raisin
in order to prevent swelling caused by humidity.

•

Clean and dry the worktop in the cutout area
thoroughly.

Worktop cutout

Prepare the cutout of the worktop according to the
dimensional drawing.

Figures in mm

Installing the hob

1111
2222
3333
4444

•

First check the factory fitted hob seal
frame to the integrity and the proper fit.

•

Put the hob with the connecting cable
with the control panel to the front into the pr
pared cutout.

•

Make sure that the distances to the cutting are
equal on all four sides and that the seal is resting
on the worktop.

•

Fix the hob depending on the worktop thickness
by attaching the enclosed brackets (3)

installation of the hob

cutout edge with wide

adhesive tape to avoid traces of jigsaw on the work-

minimum thickness of

must lie horizontally and be sealed to

the wall side against overflowing liquids or mois-

dges) must be sealed

with special varnish, silicone rubber or cast raisin
in order to prevent swelling caused by humidity.
Clean and dry the worktop in the cutout area

according to the

Hob
Gasket
Bracket
Screw

First check the factory fitted hob seal at the hob
frame to the integrity and the proper fit.
Put the hob with the connecting cable first and

control panel to the front into the pre-

Make sure that the distances to the cutting are
equal on all four sides and that the seal is resting

Fix the hob depending on the worktop thickness

brackets (3) from the

hob bottom at the provided holes and fasten them
with the screws (4).

Electrical connection

Information for the

Information for the authorized expert

authorized expert

WARNING:

•

The installation to the mains supply must conform
to the local standards and regulations.

•

Connecting the appliance to a domestic power
socket or using multiple sockets or extension c
bles is not permitted.

•

Improper connection may cause to an
shock

shock

shock!

•

Before connecting, ensure that the power supply
corresponds with the information on the rating l
bel (appliance bottom) an

•

Fix the mains cable in the tension relief.

•

The electrical installation must have an isolation
device which lets you disconnect the appliance at
all poles from the power supply.
device shall be executed with a contact width of
min. 3 mm.

•

Arrange the mains cable in such a way that it
does not get in contact with any hot components
of the appliance. Do not lead it over sharp edges
or corners.

Mains socket

Mains socket
The socket must be connected according to the
standards to a single-pole circuit breaker. The co
nection is shown below:

NOTE

NOTE: : : :

L1-brown L2

L2-black P3

P3-green-

hob bottom at the provided holes and fasten them

authorized expert

The installation to the mains supply must conform
to the local standards and regulations.

appliance to a domestic power

socket or using multiple sockets or extension ca-

Improper connection may cause to an electric

electric

Before connecting, ensure that the power supply
corresponds with the information on the rating la-

) and the wiring diagram.

Fix the mains cable in the tension relief.
The electrical installation must have an isolation
device which lets you disconnect the appliance at
all poles from the power supply. The disconnect

ted with a contact width of

Arrange the mains cable in such a way that it
does not get in contact with any hot components
of the appliance. Do not lead it over sharp edges

The socket must be connected according to the

pole circuit breaker. The con-

-yellow N1

N1-blue N2

N2-grey