background image

14 

HUSKY 800 & 900 
Belt adjustment and replacement. 
To Remove PTO Belt 

1.  Move  Speed  Range  lever  halfway  between  low  

and  high  range  so  that  belt  tightener  does  not 
contact the belts. 

2.  Loosen belt guide from PTO support and remove 

PTO belt from pulley. 

3. Loosen the two capscrews (A) that hold belt guides 

to  engine  –  just  enough  to  swing  guides  away 
from engine pulley. 

4. Remove the two drive belts from engine pulley. 
5. Remove PTO belt. 
To install PTO belt, reverse the above procedure. 

Be sure belt guides are properly positioned on the 
engine.

  Locator on back of belt guide should fit into 

groove on face of engine. 

To Remove Drive Belts 

1. Follow steps 1, 2, 3, and 4 listed above. 
2.  Remove  nut  and  washers  from  front  end  of  the 

drive  shaft,  (To  keep  driveshaft  from  turning 
while removing nut, hold it with a wrench across 
T bar welded to back end of driveshaft.) 

3.  Remove  the  four  capscrews  (B)  and  washers 

that hold bearing support to the mounting plate 
assembly. 

4.  Remove  bearing  support  by  sliding  it  off  front 

end of driveshaft. 

5. Remove drive belts. 
To install new belts reverse the above procedure.  

Be sure belt guides are properly positioned on the 
engine.   

Locator  on  back  of  belt  guide  should  fit 

into groove on face of engine. 

PTO Belt Adjustment 

The  PTO  belt  can  be  adjusted  by  loosening  the 
three capscrews (C) that hold PTO support casting 
 
 
 

to axle support casting.  Raise or lower PTO support 
casting to proper adjustment. 
 

Drive Belt Adjustment 

The  drive  belts  can  be  adjusted  by  loosening  the 
four  capscrews  (B)  holding  the  bearing  support 
plate to mounting plate.  Raise or lower the bearing 
support plate to proper adjustment. 

IMPORTANT:   

A  loose  drive  belt  will  slip  under 

load  and  one  that  is  too  tight  will  drag  in  the 
pulleys.  Proper adjustment of belts will allow belt 
tightener pulley to move approximately two inches 
from  disengaged  position  before  it  is  stopped  by 
belt. 
If  belts  are  properly  adjusted  (as  described  above) 
and  still  drag,  check  adjustment  of  lower  belt 
guide.    There  should  be  approximately  1/8” 
clearance  between  pulley  and  belt  guide  all  the 
way around. 
 
 

   

  

Adjustments  

 

Содержание Husky 600

























Отзывы: