Bogen Nyquist C4000 Series Скачать руководство пользователя страница 120

Страница: 120 / 146

108

6.2.1

Managing Exclusion and Vacancy Lists

A station added to the Vacancy List and a station added to the Exclu-

sion List both appear gray on the Admin Station’s Check-In page if

the Check-In page is configured to display these lists. The difference

between the two lists, though, is that stations on the Exclusion List

should always be excluded from the check-in process. Those on the

Vacancy List, are stations (classrooms or areas) that normally would

be checking in but may be vacant when the check-in process is

started.
A station on the vacancy list can still check in. This could occur during

an emergency situation where a normally vacant classroom becomes

Table 6-3, Check-In Configuration Options

Enabled

Specifies if Manage Check-In can be used. If

Disabled

, you can configure Manage Check-

In options but you cannot start the check-in

process.

Enable audio
prompts and con-
firmation mes-
sages

Specifies if audio files will be used as part of

Manage Check-In.

When enabled, audio prompts and audio

feedback play at stations when the stations

perform check-in. If disabled, no audio

prompts or audio feedback are played on the

station.

When feedback is disabled, stations checking

in with digital call switches will see a ringing

status (flashing green) for about 2 seconds

while checking in. Stations checking in with

IP phones will notice a call lasting about 2

seconds.

Vacancy List

Specifies the stations to be added to the

Vacancy List (see

"Managing Exclusion and

Vacancy Lists” on page 108

Exclusion List

Specifies the stations to be added to the

Exclusion List (see

"Managing Exclusion and

Vacancy Lists” on page 108

Содержание Nyquist C4000 Series


















































































































































Результаты поиска

Содержание Nyquist C4000 Series

Отзывы:

Похожие инструкции для Nyquist C4000 Series

Бренды по названию

Популярные бренды

Bogen Nyquist C4000 Series, Руководство пользователя

Результаты поиска

Содержание Nyquist C4000 Series

Отзывы:

Похожие инструкции для Nyquist C4000 Series

Бренды по названию

Популярные бренды