BodyCraft GL Скачать руководство пользователя страница 12

Страница: 12 / 21

STEP 5 INSTALL TOP CABLE

Pulleys T3 and T5 are mounted to either side of the steel tab. Do not mount both pulleys to

one side. Assemble cables and pulleys simultaneously

1. See Fig. T1 Run the threaded end of the

TOP CABLE (74)

over p

ulley T1

at the front of the

TOP FRAME (2)

and secure using one

3/8" X 1-3/4" HEX HEAD BOLT (84)

and one

3/8"

NYLA-NUT (104)

2. See Fig. T2,T4 Run the cable backand over

pulley T2

mounted onto the

FRONT UPRIGHT(2)

and secure using one

3/8" X 1-3/4" HEX HEAD BOLT (84)

and one

3/8" NYLA-NUT (104)

3. See Fig. T3,T5 Loosely preinstall

PULLEYS

onto each side of the tab welded to the

PRESS

ARM SUPPORT (12)

using one

3/8" X 3" HEX HEAD BOLT (82)

, two

3/8" WASHERS (100)

and one 3

/8" NYLA-NUT (104)

NOTE: MAKE SURE NOT TO INSTALL BOTH PULLEYS TO ONE SIDE OF THE TAB.

Route the cable to the top of

pulley T3

(T3 is the pulley on the right side as if siting on the seat)

around to the underside of

pulley T4

, exiting the top and then forward and overtop of

(left

side pulley). The cable should now be exiting the underside of

4. See Fig. T6 Route

Cable

under

Pulley T6

mounted inside the

FRONT UPRIGHT (3)

and secure

using one

3/8" X 3" HEX HEAD BOLT (82)

, two

3/8" WASHERS (100)

, two

3/8" ID FLANGE

BUSHINGS (65)

and one

3/8" NYLA-NUT (104)

5. See Fig. T7 Route cable over top of

Pulley T7

you will mount in the rear bracket on the

TOP

FRAME (2)

using one

3/8" X 2-3/4" HEX BOLT (83)

and one

3/8" NYLA-NUT (104)

6. See Fig. T8 Mount a pulley in the closed end of the

ADJUSTABLE PULLEY BLOCK (13)

using

one

3/8" X 1-3/4" HEX HEAD BOLT (84)

and one

3/8" NYLA-NUT (104)

. Hang this

ADJUSTABLE PULLEY BLOCK (13)

by routing the cable to the underside of the pulley as

shown in

. Continue routing the cable over top of

Pulley T9

, which you will mount to

TOP

FRAME (2)

using one

3/8" X 1-3/4" HEX HEAD BOLT (84)

and one

3/8" NYLA-NUT (104)

7. See Fig. T9,T11 Route the cable over

Pulley T9

mounted to the

TOP FRAME (2)

using one

3/8"

X 1-3/4" HEX HEAD BOLT (84)

and one

3/8" NYLA-NUT (104)

8. See Fig. T10 Then run the cable through the

FLOATING PULLEY BLOCK (15)

. Orient the

FLOATING PULLEY BLOCK (15)

with the threaded end up, flat side down. Threaded installed

1/2" HALF THREADED STUD (93)

to bracket welded on

TOP FRAME (2)

. Insert a pulley into

the

FLOATING PULLEY BLOCK (15)

, making sure the cable runs to the underside. Secure the

pulley using one

3/8" X 1-3/4" HEX HEAD BOLT (84)

and one

3/8" NYLA-NUT (104)

. If you

purchased option LEG PRESS at same time, please orient the

FLOATING PULLEY BLOCK

(15)

, with the threaded end down, flat side up as

LEG PRESS

manual.

9. Screw the threaded end of the

TOP CABLE (74)

into the

TOP PLATE (32)

about half way.

10. Adjust

TOP CABLE (74)

to remove all slack by loosening the Stop at the top of

Pulley T8

. The

Bolt

in the

TOP PLATE (32)

can also be adjusted.

NOTE:

This

BOLT

must always be at least

1/3 of the way into the

TOP PLATE (32)

TIGHTEN the JAM NUTS at both Adjustment

points.

Note: If you have purchased the optional Leg press Station,

the FLOATING PULLEY BLOCK (15) will mounted

differently, please refer to the Leg Press Manual.

Содержание GL






















Результаты поиска

Содержание GL

Отзывы:

Похожие инструкции для GL

Бренды по названию

Популярные бренды

BodyCraft GL, Руководство пользователя

Результаты поиска

Содержание GL

Отзывы:

Похожие инструкции для GL

Бренды по названию

Популярные бренды