BMW R 1100 GS + Adventure Скачать руководство пользователя страница 195

Страница: 195 / 464

21.7

Removing and installing clutch

•

Remove dualseat.

•

[RT]

Remove mirror.

•

[RS/GS/RT]

Remove side sections of fairing.

•

[RS]

Detach inner cockpit panel at fuel tank.

•

[R]

Remove fuel tank cover.

•

Unscrew fuel tank mount.

•

Seal, loosen and pull off fuel feed and return line
with hose clip,

BMW No. 13 0 010

•

Remove vent pipes.

•

Separate plug for fuel pump.

•

Remove fuel tank.

•

Remove battery.

Caution:

Disconnect negative terminal from battery first, then
positive terminal. Connect the positive battery termi-
nal first, then the negative terminal.

•

Motorcycles with throttle-cable divider, release
Bowden-cable divider.

•

Unscrew rear battery mount.

•

Remove plug from air temperature sensor.

•

Remove air cleaner cover.

•

Detach air intake pipe and push it into the air
cleaner housing.

•

Remove front/rear air cleaner box.

•

Remove muffler.

•

Unfasten plug connector for neutral switch and
side stand switch/detach leads.

•

Disconnect plug for brake light switch and de-
tach lead.

•

[ABS]/[GS/R/RT]

Detach the plug connection at

the rear sensor line and the line itself.

•

Remove brake fluid reservoir from holder.

•

Remove rear brake pipe from holder.

•

Unfasten screw connection on rear frame/only
loosen mount at front of struts.

•

Remove suspension strut.

•

Tilt rear frame upwards and secure with strap (1).

•

[ABS]

Detach rear brake caliper.

•

[ABS]

Take off right footrest plate.

•

Unfasten/remove fuel pipe from injector.

•

Remove cable connector/wiring harness from air
cleaner box.

•

Detach return line/oil trap from air cleaner box.

•

Remove air cleaner box.

•

Disconnect clutch cable from gearbox.

•

[RS/GS/R]

Take off starter motor cover/pull off

wire to power socket.

•

Detach leads at starter motor.

•

Remove starter motor.

RS230310

Содержание R 1100 GS + Adventure

















































































































































































































































































































































































































































































Результаты поиска

Содержание R 1100 GS + Adventure

Отзывы:

Бренды по названию

Популярные бренды

BMW R 1100 GS + Adventure, Руководство по ремонту

Результаты поиска

Содержание R 1100 GS + Adventure

Отзывы:

Бренды по названию

Популярные бренды