Blueprint Subsea seatrac X100 Series Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 140

Blueprint Subsea seatrac X100 Series Скачать руководство пользователя страница 84

SeaTrac Serial Command Interface Reference

Page 84

7.4.2.

CID_SETTINGS_SET

The CID_SETTINGS_SET command is issued to update the values of the working RAM settings
and apply the new values.
This command updates the entire contents of the settings record, so for modification of
settings it is recommended to first use

CID_SETTINGS_GET

command to read the current

settings record, then modify and resend this.

This command does not save the new settings into permanent EEPROM storage and so
changes made will be lost if the device is powered down or rebooted.
To store changes after the set command, use the

CID_SETTINGS_SAVE

Not all settings will be applied after the set command is issued. Specifically
communication baud-rate settings will only be applied when the device is next power
up, or a

command is issued.

structure definition for details of which settings are only applied

on power-up/reboot.

Command Message Parameters

Parameter Type Description

MSG_ID

Command

identification code (CID_SETTINGS_SET)

SETTINGS

Structure containing the new settings to apply.

Response Message Parameters

Parameter Type Description

MSG_ID

Command

identification code (CID_SETTINGS_SET)

STATUS

Status code used to indicate if the command
executed successfully.
Valid values are…



CST_OK – The command was performed
successfully.



CST_CMD_PARAM_MISSING - The settings
parameter were not specified correctly.

«
...
82
83
84
85
86
...
»

Содержание seatrac X100 Series













































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды