manualshive.com logo in svg

Blueprint Subsea seatrac X100 Series, Руководство пользователя

Поделиться
Скачать
Blueprint Subsea seatrac X100 Series Скачать руководство пользователя страница 83

 

SeaTrac Serial Command Interface Reference

 

 

Page 83 

 

7.4.

 

Settings Messages 

The beacon settings system is responsible for the retrieval, verification, application and 
storage of parameters determining the operation of the beacon. 
 
All settings are stored within a single “settings record” and at power-up this is loaded from 
permanent (non-volatile) EEPROM memory into the working RAM area. 
 
Any changes made to the settings record by the user (through the 

CID_SETTINGS_SET

 

command) are always made to the working RAM set and will be lost if the device is powered 
down before a 

CID_SETTINGS_SAVE

 command is issued to update the EEPROM copy. 

 
When new settings are specified by the 

CID_SETTINGS_SET

 command most will be applied 

immediately. However, some settings such as those controlling communications baud-rates etc 
are only applied when the device is powered up (or restarts via a 

CID_SYS_REBOOT

 

command). See the 

SETTINGS_T

 structure definition for details of which settings are only 

applied on power-up/reboot. 
 

 

The EEPROM memory used to permanently store the settings information in the beacon 
has a lifetime endurance of between 10,000 and 50,000 write cycles, after which its 
data retention capabilities may start to degrade (below the guaranteed 5 year period). 
 
For this reason, only store the working RAM settings when required with the 

CID_SETTINGS_SAVE

 command. When designing a control system, ensure that 

settings are only stored infrequently and when needed (i.e. not on a periodic basis that 
may reduce operating life). 

 

7.4.1.

 

CID_SETTINGS_GET 

The CID_SETTINGS_GET command is issued to read back the settings record from working 
RAM containing the values currently in use.  
 

Command Message Parameters 

Parameter Type Description 

MSG_ID 

CID_E

 Command 

identification code (CID_SETTINGS_GET) 

 

Response Message Parameters 

Parameter Type Description 

MSG_ID 

CID_E

 Command 

identification code (CID_SETTINGS_GET) 

SETTINGS 

SETTINGS_T

 

Structure containing the current working RAM 
settings in use. 

 

Содержание seatrac X100 Series













































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды