Blue Summit BG961UHE Скачать руководство пользователя страница 46

Страница: 46 / 56

507768-02B

Page 46 of 56

Issue 1904

6. If flame is not detected after first ignition trial, the

ignition control will repeat steps 3 and 4 four more

times before locking out the gas valve. The ignition

control will then automatically repeat steps 1 through

6 after 60 minutes. To interrupt the 60 minute period,

move thermostat from “Heat” to “OFF” then back to

“Heat”. Heating sequence then restarts at step 1.

Gas Pressure Adjustment

Gas Flow (Approximate)

Gas Meter Clocking Chart

Capacity

Seconds for One Revolution

Natural

1 cu ft

Dial

2 cu ft

Dial

1 cu ft

Dial

2 cu ft

Dial

-045

160

200

400

-070

110

136

272

-090

102

204

-110

164

Natural-1000 btu/cu ft LP-2500 btu/cu ft

Table 9.

Furnace should operate at least 5 minutes before checking

gas flow. Determine time in seconds for two revolutions

of gas through the meter. (Two revolutions assures a

more accurate time.) Divide by two and compare to time

in Figure 68. If manifold pressure matches Table 11 and

rate is incorrect, check gas orifices for proper size and

restriction. Remove temporary gas meter if installed.

NOTE:

To obtain accurate reading, shut off all other gas

appliances connected to meter.

Supply Pressure Measurement

When testing supply gas pressure, use the 1/8” N.P.T.

plugged tap or pressure post located on the gas valve to

facilitate test gauge connection. See Figure 69. Check

gas line pressure with unit firing at maximum rate. Low

pressure may result in erratic operation or underfire. High

pressure can result in permanent damage to gas valve or

overfire.

On multiple unit installations, each unit should be checked

separately, with and without other units operating. Supply

pressure must fall within range listed in Table 11.

Manifold Pressure Measurement

1. Remove the threaded plug from the outlet side of

the gas valve and install a field provided barbed

fitting. Connect to a manometer to measure manifold

pressure.

2. Start unit and allow 5 minutes for unit to reach steady

state.

3. While waiting for the unit to stabilize, observe the

flame. Flame should be stable and should not lift from

burner. Natural gas should burn blue.

4. After allowing unit to stabilize for 5 minutes, record

manifold pressure and compare to value given in

Table 11.

NOTE:

Shut unit off and remove manometer as soon as an

accurate reading has been obtained. Take care to remove

barbed fitting and replace threaded plug.

Proper Combustion

Furnace should operate minimum 15 minutes with correct

manifold pressure and gas flow rate before checking

combustion. Take combustion sample beyond the flue

outlet and compare to the tables below.

Table 10.

Capacity

% for Nat

% for L.P.

All

7.2 - 7.9

8.6 - 9.3

The maximum carbon monoxide reading should not exceed

100 ppm.

Table 11.

Manifold and Supply Line Pressure 0-10,000 ft.

Capacity

Gas

Manifold Pressure in. w.g.

Supply Line Pressure

in. w.g.

0-10,000 ft.

0-4500 ft.

4501-5500 ft.

5501-6500 ft.

6501-7500 ft. 7501-10000 ft.

All Sizes

Natural

3.5

3.3

3.2

3.1

3.5

4.5

13.0

LP /

Propane

10.0

9.4

9.1

8.9

10.0

11.0

13.0

NOTE

: A natural to LP propane gas changeover kit is necessary to convert this unit. Refer to the changeover kit installation

instruction for the conversion procedure.

Содержание BG961UHE

























































Результаты поиска

Содержание BG961UHE

Отзывы:

Похожие инструкции для BG961UHE

Бренды по названию

Популярные бренды

Blue Summit BG961UHE, Руководство по установке

Результаты поиска

Содержание BG961UHE

Отзывы:

Похожие инструкции для BG961UHE

Бренды по названию

Популярные бренды