Blue Summit BG952UHV Скачать руководство пользователя

Страница: 10 / 56

507266-04B

Page 10 of 56

Issue 1904

Installation

Setting Equipment

Do not connect the return air ducts to the back of the

furnace. Doing so will adversely affect the operation of

the safety control devices, which could result in personal

injury or death.

WARNING

Blower access panel must be securely in place when

blower and burners are operating. Gas fumes, which

could contain carbon monoxide, can be drawn into

living space resulting in personal injury or death.

WARNING

Upflow Applications

The gas furnaces can be installed as shipped in the upflow

position. Refer to Figure 12 for clearances. Select a location

that allows for the required clearances that are listed on

the unit nameplate. Also consider gas supply connections,

electrical supply, vent connection, condensate trap and

drain connections, and installation and service clearances

[24 inches (610 mm) at unit front]. The unit must be level

from side to side. Tilt the unit slightly (maximum 1/2 in.

from level) from back to front to aid in the draining of the

heat exchanger. See Figure 13.

Allow for clearances to combustible materials as indicated

on the unit nameplate.

Figure 12. Installation Clearances

Top/Plenum

1 in. (25 mm)

*Front

Back

Sides

0†

Vent

Floor

0‡

* Front clearance in alcove installation must be 24 in. (610

mm). Maintain a minimum of 24 in. (610 mm) for front service

access.
† Allow proper clearances to accommodate condensate trap

and vent pipe installation.
‡ For installations on a combustible floor, do not install

the furnace directly on carpeting, tile or other combustible

materials other than wood flooring.

Figure 13. Setting Equipment

Tilt the unit slightly (Max. 1/2”) from back to front to aid in the draining of the heat exchanger.

Unit must be level side-to-side in all applications.

Содержание BG952UHV

























































Результаты поиска

Содержание BG952UHV

Отзывы:

Похожие инструкции для BG952UHV

Бренды по названию

Популярные бренды

Blue Summit BG952UHV, Руководство по установке

Результаты поиска

Содержание BG952UHV

Отзывы:

Похожие инструкции для BG952UHV

Бренды по названию

Популярные бренды