Blue Summit BG952UHV Скачать руководство пользователя

Страница: 56 / 56

507266-04B

Page 56 of 56

Issue 1904

Requirements for Commonwealth of Massachusetts

Modifications to NFPA-54, Chapter 10

Revise NFPA-54 section 10.8.3 to add the following

requirements:

For all side wall, horizontally vented, gas-fueled equipment

installed in every dwelling, building or structure used in

whole or in part for residential purposes, including those

owned or operated by the Commonwealth and where the

side wall exhaust vent termination is less than seven (7)

feet above the finished grade in the area of the venting,

including but not limited to decks and porches, the following

requirements shall be satisfied:

INSTALLATION OF CARBON MONOXIDE

DETECTORS

. At the time of installation of the side

wall, horizontally vented, gas-fueled equipment, the

installing plumber or gas fitter shall observe that a

hard-wired carbon monoxide detector with an alarm

and battery backup is installed on the floor level where

the gas equipment is to be installed. In addition, the

installing plumber or gas fitter shall observe that a

battery-operated or hard-wired carbon monoxide

detector with an alarm is installed on each additional

level of the dwelling, building or structure served by the

side wall, horizontally vented, gas-fueled equipment.

It shall be the responsibility of the property owner to

secure the services of qualified licensed professionals

for the installation of hard-wired carbon monoxide

detectors.

a. In the event that the side wall, horizontally

vented, gas-fueled equipment is installed in a

crawl space or an attic, the hard-wired carbon

monoxide detector with alarm and battery backup

may be installed on the next adjacent floor level.

b. In the event that the requirements of this subdivision

cannot be met at the time of completion of

installation, the owner shall have a period of thirty

(30) days to comply with the above requirements;

provided, however, that during said thirty (30)

day period, a battery-operated carbon monoxide

detector with an alarm shall be installed.

APPROVED CARBON MONOXIDE DETECTORS.

Each carbon monoxide detector as required in

accordance with the above provisions shall comply

with NFPA 720 and be ANSI/UL 2034 listed and IAS

certified.

SIGNAGE

. A metal or plastic identification plate shall

be permanently mounted to the exterior of the building

at a minimum height of eight (8) feet above grade

directly in line with the exhaust vent terminal for the

horizontally vented, gas-fueled heating appliance or

equipment. The sign shall read, in print size no less

than one-half (1/2) inch in size, “

GAS VENT DIRECTLY

BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS.

”

INSPECTION

. The state or local gas inspector of the

side wall, horizontally vented, gas-fueled equipment

shall not approve the installation unless, upon

inspection, the inspector observes carbon monoxide

detectors and signage installed in accordance with the

provisions of 248 CMR 5.08(2)(a) 1 through 4.

EXEMPTIONS: The following equipment is exempt

from 24 CMR 5.08(2)(a) 1 through 4:

1. The equipment listed in Chapter 10 entitled “Equipment

Not Required to Be Vented” in the most current edition

of NFPA 54 as adopted by the Board; and

2. Product Approved side wall, horizontally vented, gas-

fueled equipment installed in a room or structure

separate from the dwelling, building or structure used

in whole or in part for residential purposes.

MANUFACTURER REQUIREMENTS - GAS EQUIPMENT

VENTING SYSTEM PROVIDED.

When the manufacturer of Product Approved side wall,

horizontally vented, gas-fueled equipment provides a

venting system design or venting system components

with the equipment, the instructions provided by the

manufacturer for installation of the equipment and the

venting system shall include:

1. Detailed instructions for the installation of the venting

system design or the venting system components: and

2. A complete parts list for the venting system design or

venting system.

MANUFACTURER REQUIREMENTS - GAS EQUIPMENT

VENTING SYSTEM NOT PROVIDED.

When the manufacturer of Product Approved sidewall,

horizontally vented, gas-fueled equipment does not

provide the parts for venting the flue gases, but identifies

“special venting systems,” the following requirements shall

be satisfied by the manufacturer:

1. The referenced “special venting system” instructions

shall be included with the appliance or equipment

installation instructions; and

2. The “special venting systems” shall be Product

Approved by the Board, and the instructions for that

system shall include a parts list and detailed installation

instructions.

A copy of all installation instructions for all Product

Approved side wall, horizontally vented, gas-fueled

equipment, all venting instructions, all parts lists

for venting instructions, and/or all venting design

instructions shall remain with the appliance or

equipment at the completion of the installation.

Содержание BG952UHV

























































Результаты поиска

Содержание BG952UHV

Отзывы:

Похожие инструкции для BG952UHV

Бренды по названию

Популярные бренды

Blue Summit BG952UHV, Руководство по установке

Результаты поиска

Содержание BG952UHV

Отзывы:

Похожие инструкции для BG952UHV

Бренды по названию

Популярные бренды