background image

TO REDUCE THE RISK OF A RANGETOP GREASE FIRE (CONTINUED): 



IF YOU ARE FLAMING LIQUOR OR OTHER SPIRITS, AND YOUR APPLIANCE IS INSTALLED UNDER 
A VENT HOOD, TURN THE FAN OFF.  THE DRAFT CREATED COULD CAUSE THE FLAMES TO 
SPREAD OUT OF CONTROL. 



FOR YOUR SAFETY, NEVER USE YOUR APPLIANCE OR ANY OTHER COOKING APPLIANCE AS A 
SPACE HEATER TO WARM OR HEAT THE ROOM. 



USE ONLY DRY POTHOLDERS.  MOIST OR DAMP POTHOLDERS ON HOT SURFACES MAY RESULT 
IN STEAM BURNS.  DO NOT ALLOW POTHOLDERS TO TOUCH HOT BURNER AREAS.  DO NOT USE 
A TOWEL OR OTHER BULKY MATERIAL AS A POTHOLDER. 



TO REDUCE THE RISK OF BURNS, IGNITION OF FLAMMABLE MATERIALS, AND SPILLAGE, THE 
HANDLE OF ANY POT OR PAN SHOULD BE POSITIONED SO THAT IT DOES NOT EXTEND OVER 
ADJACENT BURNERS OR THE FRONT OF THE APPLIANCE. 



CLEAN VENTILATING FANS AND GREASE BAFFLES OFTEN.  GREASE SHOULD NOT BE ALLOWED 
TO ACCUMULATE . 

WARNING! 

WARNING! 

TO REDUCE RISK OF INJURY TO PERSONS DUE TO A GREASE FIRE: 



SMOTHER THE FLAMES WITH A CLOSE FITTING LID, COOKIE SHEET OR METAL TRAY, THEN 
TURN OFF THE BURNER.   TAKE CARE TO AVOID AND PREVENT BURNS.  IF FLAMES DO NOT EX-
TINGUISH, EVACUATE THE PRMISES AND CALL THE FIRE DEPARTMENT 



NEVER HANDLE OR PICK UP A FLAMING PAN.   



DO NOT USE WATER, INCLUDING WET DISHCLOTHS, OR TOWELS.  A VIOLENT STEAM EXPLO-
SION MAY ENSUE 



 DO NOT TURN ON HOOD TO EVACUATE SMOKE.  TURN OFF HOOD 



USE AN EXTINGUISHER ONLY IF: 



YOU HAVE A CLASS ABC EXTINGUISHER AND YOU CAN OPERATE  IT 



THE FIRE IS SMALL AND CONTAINED WHERE IT STARTED 



THE FIRE DEPARTMENT HAS BEEN NOTIFIED 



YOU CAN FIGHT THE FIRE WITH YOUR BACK TOWARDS AN UNOBSTRUCTED EXIT 

WARNING! 

P/N 750306  Page   4 



THIS PRODUCT IS FOR GENERAL VENTILATION APPLICATIONS.  DO NOT USE TO EXHAUST HAZ-
ARDOUS, FLAMMABLE, OR EXPLOSIVE MATERIALS 



PRIOR TO CLEANING OR SERVICING THE UNIT, SWITCH POWER OFF AT THE SERVICE PANEL 
AND LOCK OUT THE PANEL.  IF THE PANEL CANNOT BE LOCKED OUT, AFFIX A PROMINENT 
WARNING TAG TO THE SERVICE PANEL. 



DO NOT USE PORCELAIN OR ABRASIVE CLEANERS ON THIS PRODUCT.  THIS MAY RESULT IN 
COSMETIC DAMAGE TO THE SURFACE LIKE SCRATCHES AND/OR DISCOLORIZATION 



ALL BRASS TRIM PIECES REQUIRE SPECIAL CLEANING.  DO NOT USE ABRASIVE CLEANERS OR 
FURNITURE POLISH.  THIS WILL RESULT IN DISCOLORIZATION TO THE BRASS SURFACE  

Содержание BS-PC3024




























Отзывы: