background image

35 

Appendix A: Gas Type Conversion 

Revision 1/ 

© Moffat Ltd, January 2007 

Blue Seal Evolution Series Gas Chargrills 

Pilot Burners 
 

1. 

To remove the pilot burner, disconnect the gas sup-

ply tube from the base of the pilot burner. 

 

NOTE; Do not remove the mounting plate securing 

the pilot burner and thermo couple to the 

Chargrill.  Fig 14 shows Pilot Burner 

 

Retaining Plate removed for clarity only. 

 

2. 

Unscrew the base nut from the pilot burner and using 

a small screwdriver,withdraw injector from inside the 

pilot burner. 

3. 

Determine the correct injector size for the corre-

sponding gas from the rating plate attached to the 

inner bulkhead adjacent to the manifold test point 

behind the front control panel. 

4. 

Fit the new pilot injector into the rear of the pilot 

burner and push fully home. 

5. 

Re-connect the gas supply tube to the base of the 

pilot burner and tighten. 

Gas Supply Tube 

Fig 12 

Thermocouple 

Pilot Burner 

Piezo Igniter 

Unscrew Gas 

Supply Tube Here 

Fig 14 

Thermocouple/Pilot 
Burner/Igniter  
Retaining Plate 

Unscrew Gas 

Supply Tube Here 

Fig 13 

Содержание Evolution G592













































Отзывы: