Outdoor Portable LP Gas Griddle
Model No. GBT1860L
6
Assembly Instructions (continued)
This griddle is designed to operate with a 1 lb. 7.75
in. or 10.6 in. high disposable / 16.4 oz. or 14.1 oz.
propane gas tank (DOT 39 Cylinder) (Figure 1).
DO NOT ATTEMPT TO REFILL ANY 1 lb. (16.4 oz. or
14.1 oz.) PROPANE GAS TANKS!
Connecting LP Gas Tank
Only cylinders marked “propane” may be used.
Note: 1 lb cylinders may form frost when near empty.
1. Make sure the control knob is in the
“ OFF” position (Figure 3).
2. Lubricate the threads of the regulator with
petroleum jelly. Line up threads on LP gas tank
with regulator.
3. Insert and rotate LP gas tank clockwise until
they fit snugly together. HAND TIGHTEN ONLY. Be
careful not to crossthread when screwing in tank
(Figure 4).
4. Perform leak test per “Checking for Leaks”
section.
Disconnecting LP Gas Tank
W
CAUTION: The LP gas tank must be
removed when this appliance is not in
use.
1. Turn the control knob to the “ OFF” position
(Figure 3).
2. Rotate LP gas tank counterclockwise until it is
detached (Figure 5).
3. Store the LP gas tank in a proper location, per
instructions on the LP gas tank.
Operating Instructions
Checking for Leaks
Burner Connections
1. Make sure the regulator is securely fastened.
Note: The brass nut should be 1/4 to 1/2 turn past
tight. The regulator will rotate 360º even when the
brass nut is tightened.
2. Visually check the connection between the burner
and regulator (Figure 6).
3. Make sure the burner/venturi tube fits over the
orifice (Figure 2).
W
WARNING: Failure to inspect this
connection or follow these instructions
could cause a fire or an explosion
which can cause death, serious bodily
injury or damage to property.
4. Please refer to diagram for proper installation
(Figures 2 and 6)
5. If the burner/venturi tube does not rest flush
to the orifice, as shown, please contact
1.800.694.0013 for assistance
6. If the burner and regulator do not fit properly
or if you have any questions, please contact
1.800.694.0013 for assistance.
Tank/Gas Line Connection
1. Make 2-3 oz. of leak detection solution by mixing
one part liquid dishwashing soap with three parts
water.
2. Make sure control knob is in the “ OFF” position
(Figure 3).
3. Apply the leak detection check solution on all “X”
locations (Figure 6).
a. If any bubbles appear, remove the LP
gas tank and reconnect, making sure the
connection is secure.
b. If you continue to see bubbles after several
attempts, remove the LP gas tank per
“Disconnecting LP Gas Tank” section, and
contact 1.800.694.0013 for assistance.
c. If no bubbles appear after one minute, turn
control knob to the “ OFF” position, wipe away solution and proceed.
Installing LP Gas Tank
5
Attach Regulator
Note: Once attached, the regulator/control valve will freely rotate to accomodate the
LP gas tank.
Assembly Instructions (continued)
IMPORTANT
Before first use and after each use, always
season your griddle per “Seasoning Griddle”
section.
Figure 1
1 lb
453 g
7.75 in.
/ 19,7 cm
3.875 in. / 9,8 cm
2.9 in. / 7,4 cm
1 lb
465 g
10.6 in.
/ 27 cm
Figure 2
Burner/
Venturi Tube
LP Gas
Valve with
Orifice
LP Gas
Connection
Figure 3
OFF
APAGADO
Figure 4
Figure 5
Figure 6