Blue Diamond POWER RAKE Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 52

Blue Diamond POWER RAKE Скачать руководство пользователя страница 32

32

Power Rake Operation and Maintenance Manual

Maintenance

Side Shields and Skid

Plates

Material Side Shields Removal / Installation

Figure 11

Remove the pin (Item 1) and remove the side
shield (Item 2) and skid plate (Item 3)

[Figure 11]

on (both sides).

Skid Plate Adjustment

Figure 12

Remove the three nuts and bolts (Item 1) then
remove the skid plate (Item 2)

[Figure 12]

Align the desired skid plate holes with the side
shield (Item 3)

[Figure 12]

holes, install the bolts,

nuts and tighten.

Gauge Wheels

Gauge Wheel Adjustment

WARNING

AVOID SERIOUS INJURY OR DEATH

Securely block up the attachment before
working underneath.

Figure 13

Remove  the  retaining  pin  (Item  1)  and  lower  the
spindle  (Item  2).  Relocate  spacers  as  desired
above  or  below  the  spindle  mount  arm  (Item  4)

[Figure 13]

.

Install the spindle and install the retaining pin.

NOTE:

The gauge wheel can also be adjusted up

/ down at the spindle mount arm (Item 5)

[Figure 13]

.

Remove the four bolts, washers and nuts. Position
the spindle mount arm as desired. Install and
tighten the four bolts washers and nuts.

Repeat procedure on the other main spindle
mount.

1

2

3

1

3

2

1

2

3

4

5

«
...
30
31
32
33
34
...
»

Содержание POWER RAKE





















































Отзывы:

Нет отзывов