background image

 
 

 

 

 

 

1. Introduction  

1.1 Objective 

The manual is not a general publication but only edited for experienced technician. The 

main purpose is to provide basic foundation for the electrical & mechanical maintenance. 

1.2 General Safety notice 

1)

  Only experienced technician can repair with this guide during product is power on. Any 

maintenance by other non-technicians will cause serious damage of the handset. Neither 
short circuit nor counter-polarity connection is allowed for any electronic part in the 
handset.

 

3)

  Be careful of ESD protection during maintenance to avoid the damage of electrostatic 

sensitive components on the handset.

 

4)

  If disassembling operation is necessary for repairing, comply with mechanical structure 

disassembling work instruction. Otherwise, disassembling operation will make the 
handset damaged.

 

1.3 Use Instruction 

1) Avoid using handset in conditions following: 

  Where there is any caustic liquid or gas 

  Where there is any high-temperature or fire circumstance 

  Where there is any flammable liquid or gas 

2) Do not use handset while driving for your safety; 
3)  Please  comply  with  corresponding  rules  in  some  special  occasions  (like  in  operating 

room, in airplane) 

4) Accessory purchasing or changing should comply with model matching; 
5) If need clean handset surface, please use cloth dipping a little clean water. Do not use 

soluble cleanser. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание LIFE PLAY MINI



















Отзывы: