CAUTION:
Do not use damaged appliances. If you are in any doubt, consult an engineer.
Connection and installation of your chiller are to be carried out in strict compliance with
the relative instructions in this manual.
For safety, the appliance must be properly earthed in accordance with specifications
Do not damage any parts of the appliance which carry refrigerant by piercing,
perforating, crushing, twisting or scraping. If the refrigerant comes into contact with the
eyes, it may cause serious eye injury.
Always remember to unplug the appliance before cleaning. Never unplug your appliance
by pulling on the power cable. Always grip plug firmly and pull straight out from the
socket. Always check that the plug and cable are undamaged.
All repairs must be carried out by qualified engineers. Inadequate repairs may be
dangerous. Never try to repair the refrigerator yourself.
Should the cover of the interior light or fan fall off or break, switch the refrigerator off
immediately and replace the cover.
Ensure your chosen location has a flat and stable surface. The unit may be levelled by
turning either or both of the adjustable feet in the front corners. Check the unit is level
using a spirit level.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent
or similarly qualified persons in order to avoid hazard.
Be sure to leave at least 60mm of distance between the rear of the chiller and walls for
ventilation, 30mm distance to be allowed above and to the sides for ventilation.
Do not store explosive substances such as aerosol cans with a flammable propellant in
this appliance.
This appliance is intended for use indoor, such as shopping centre, bar room,
restaurant and so on, but not for household use.
This appliance noise is less than 65dB.
The Maximum load for a shelf is 30Kg.
Do not obstruct or cover the ventilation aperture.
Do not allow children to play with the appliance, or to sit on it or to hang onto the door.
Make sure there is a suitable power Outlet (220-240V/50Hz, 13 amps outlet) with
proper grounding to power the refrigerator.
This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge
if they have been given supervision or instruction concerning use of the appliance in a
safe way and understand the hazards involved. Cleaning and user maintenance shall not
be made by children without supervision.
Do not position this appliance with its rear panel directly against a wall. For good
circulation and operating efficiency, the ventilation grilles must never be blocked.
Ventilation should be provided above and to each side of the unit and must never be
built into a cupboard.
BEFORE USING FOR THE FIRST TIME
Remove all packaging and place the chiller on a stable, secure flat surface. Position the chiller
away from heat sources, where the unit is well-ventilated and protected from moisture, or
extremes of heat or cold. The refrigerator may not function properly if the temperature rises
above +30
℃
(standard models). The refrigerator meets the operating conditions according to climate class
4.
A 13A fuse is fitted. Never replace with a fuse rated higher than this.
NEVER USE AN EXTENSION LEAD. If the mains cable will not reach the nearest
socket, either rearrange your store layout or ask a qualified electrician to fit a new socket.
If power is cut off, wait for at least 5 minutes before plugging the unit in again to avoid
damaging the compressor.
Remove thermometer from packaging and position on the front panel and insert the sensor jack plug.
Do not place combustible, explosive or volatile articles, corrosive acid or alkali, or liquid in
glass containers into the chiller. Always exercise caution if adjusting the temperature.
PLUG IN
Once plugged in the display will show the temperature inside the chiller and the compressor
will after a short delay (the indicator light of cooling will on at the same time). This temperature is
the actual temperature recorded by the probes inside the chiller and as the chiller cools to
the set point so the number on the display will descend accordingly.
OPERATING FRONT PANEL CONTROLLER
Set point temperature press the SET button for one second the current set point
will flash display, then press the arrow buttons to change the set point,
select the desired target and then press the button to confirm the new value.
NOTE!
The MED140 controller is locked at a set point of 5°C, the display will fluctuate between 5° and 6°C
through normal use. At these settings your product will be safely stored between the recommended
temperatures b2°C and +8°C
SETTING UP AND OPERATING THE ALARM THERMOMETER (ac/-0.5°C, sampling period
10Secs, resolution 0.1°C)
(this is supplied in a box inside the cabinet and needs locating on the top panel)
NOTE! From NEW, the battery needs inserting into the thermometer by opening the door on the rear of the
alarm thermometer and the alarm settings need adjusting to suit. The battery can be found in the lower
partition of the thermometer box. If the thermometer appears low battery, do not continue to use, replace
the battery immediately. The battery is a CR2450 coin cell type battery.
Max/Min button
, short press and release, displays Max (flashing) = Max temp recorded, Min (flashing) =
Min temp recorded, press and hold resets the MAX/MIN temperature logging.
Int/Ext button
, switches display to show
IN
(when the display is fitted outside the storage area relates to
the ambient temperature)
OUT
(relates to the cold storage temperature)
NOTE!
ensure
OUT
is always
displayed
. The probe jack plug (fitted on the cabinet) will need inserting into the LH side of the thermometer.
Alarm button
, short press and release, switches on and off the audible alarm,
ensure AL (alarm on) is
always shown on the display screen once the unit is at the desired temperature
. Press and hold
adjusts the HI and LO alarm set points(flashing), use the °C/°F button on the rear of the thermometer to
adjust the alarm set points.
NOTE!
The Alarm thermometer requires setting to alarm at
LO = +2°C
HI = +8°C
Light button
, press to momentarily illuminate the back of the thermometer display
