background image

Lit. No. 43573/43583/43593, Rev. 02 

January 15, 2017

SAFETY

SAFETY PRECAUTIONS

Improper installation and operation could cause 

personal injury and/or equipment and property 

damage. Read and understand labels and the 

Owner's Manual before installing, operating, or 

making adjustments.

 WARNING

•  Driver to keep bystanders minimum of 

25 feet away from operating spreader.

•  Before working with the spreader, secure all 

loose-fitting clothing and unrestrained hair.

•  Before operating the spreader, verify that all 

safety guards are in place.

•  Before servicing the spreader, wait for 

conveyor, auger, and spinner to stop.

•  Do not climb into or ride on spreader.

 WARNING

Do not install the control for this product in 

the deployment path of an air bag. Refer to 

vehicle manufacturer's manual for air bag 

deployment area(s).

 CAUTION

If rear directional, CHMSL light, or brake 

stoplights are obstructed by the spreader, the 

lights shall be relocated, or auxiliary directional 

or brake stoplights shall be installed.

 CAUTION

Disconnect electric and/or hydraulic power 

and tag out if required before servicing or 

performing maintenance.

NOTE: Lubricate grease fittings after each use. 

Use a good quality multipurpose grease.

FUSES

The electrical system contains several blade-style 

automotive fuses. If a problem should occur and 

fuse replacement is necessary, the replacement 

fuse must be of the same type and amperage rating 

as the original. Installing a fuse with a higher rating 

can damage the system and could start a fire. Fuse 

Replacement, including fuse ratings and locations, 

is located in the Maintenance section of the Owner's 

Manual.

 WARNING

 

Overloading could result in an 

accident or damage. Do not exceed 

GVWR or GAWR ratings as found 

on the driver‑side vehicle door 

cornerpost. See Loading section to determine 

maximum volumes of spreading material.

 CAUTION

 

DO NOT leave unused material in 

hopper. Material can freeze or solidify, 

causing unit to not work properly. 

Empty and clean after each use.

 CAUTION

During the hopper installation we recommend 

the addition of an OSHA compliant Backup 

Alarm. This alarm is required for OSHA 

governed employers.

 CAUTION

 • Do not operate a spreader in need of 

maintenance.

 • Before operating the spreader, reassemble 

any parts or hardware removed for cleaning 

or adjusting.

 • Before operating the spreader, remove 

materials such as cleaning rags, brushes, 

and hand tools from the spreader.

 • Before operating the spreader, read the 

engine owner's manual, if so equipped.

 • While operating the spreader, use auxiliary 

warning lights, except when prohibited by law.

•  Tighten all fasteners according to the 

Torque Chart. Refer to Torque Chart for the 

recommended torque values.

Содержание ICE CHASER 78903



















Отзывы: