background image

Lit. No. B64045, Rev. 04 

May 15, 2016

SAFETY PRECAUTIONS

Improper installation and operation could cause 

personal injury and/or equipment and property damage. 

Read and understand labels and the Owner's Manual 

before installing, operating or making adjustments.

PERSONAL SAFETY

•  Remove ignition key and put the vehicle in park or 

in gear to prevent others from starting the vehicle 

during installation or service.

• 

Wear only snug-fitting clothing while working on 

your vehicle or snowplow.

•  Do not wear jewelry or a necktie, and secure long 

hair.

•  Wear safety goggles to protect your eyes from 

battery acid, gasoline, dirt and dust.

•  Avoid touching hot surfaces such as the engine, 

radiator, hoses and exhaust pipes.

• 

Always have a fire extinguisher rated BC handy, 

for flammable liquids and electrical fires.

FIRE AND EXPLOSION

Be careful when using gasoline. Do not use gasoline 

to clean parts. Store only in approved containers away 

from sources of heat or flame.

CELL PHONES

A driver's first responsibility is the safe operation of 

the vehicle. The most important thing you can do 

to prevent a crash is to avoid distractions and pay 

attention to the road. Wait until it is safe to operate 

Mobile Communication Equipment such as cell phones, 

text messaging devices, pagers or two‑way radios.

VENTILATION

SAFETY

 WARNING

Gasoline is highly flammable and gasoline 

vapor is explosive. Never smoke while 

working on vehicle. Keep all open flames 

away from gasoline tank and lines. Wipe up 

any spilled gasoline immediately.

 WARNING

Lower the blade when vehicle is parked. 

Temperature changes could change 

hydraulic pressure, causing the blade to 

drop unexpectedly or damaging hydraulic 

components. Failure to do this could result in 

serious personal injury.

 CAUTION

Refer to the Power Match selection system 

for minimum vehicle recommendations and 

ballast requirements.

 WARNING

Do not exceed GVWR or GAWR including the 

blade and ballast. The rating label is found on 

the driver-side vehicle door cornerpost.

 WARNING

Remove blade assembly before placing 

vehicle on hoist.

 WARNING

The driver shall keep bystanders clear of the 

blade when it is being raised, lowered or angled. 

Do not stand between the vehicle and the blade 

or within 8 feet of a moving blade. A moving or 

falling blade could cause personal injury.

 WARNING

Keep hands and feet clear of the blade and 

A-frame when mounting or removing the 

snowplow. Moving or falling assemblies could 

cause personal injury.

 WARNING

To prevent accidental movement of the blade, 

always turn the control OFF whenever the 

snowplow is not in use. The power indicator 

light will turn OFF.

 WARNING

Vehicle exhaust contains lethal fumes. 

Breathing these fumes, even in low 

concentrations, can cause death. Never 

operate a vehicle in an enclosed area without 

venting exhaust to the outside.

Содержание B32057









Отзывы: