Blizzard Lighting Wink Скачать руководство пользователя страница 18

Страница: 18 / 20

Page 18

Wink™ User Manual - Rev. A

Troubleshooting

Symptom

Solution

Fixture Auto-Shut Off

Check the fan in the fixture. If it is stopped or moving slower

than normal, the unit may have shut itself off due to high heat.

This is to protect the fixture from overheating. Clear the fan of

obstructions, or return the unit for service.

Beam is Dim

Check optical system and clean excess dust/grime.

No Power

Check fuse, AC cord and circuit for malfunction.

Blown Fuse

Check AC cord and circuit for damage, verify that moving parts

are not restricted and that unit’s ventilation is not obstructed

Slow Movement

Check that speed channels are set appropriately.

Fixture Not Respond-

ing / Responding

Erratically

Make sure all connectors are seated properly and securely.

Use Only DMX Cables.

Install a Terminator.

Check all cables for defects.

Reset fixture(s).

Tech Specs!

Weight & Dimensions

Width

8.3 inches (210 mm)

Depth

6.5 inches (164 mm)

Height

12.1 inches (306.6 mm)

Weight

12.5 lbs. (5.7 kg)

Power

Operating Voltage

100V-240VAC, 50-60Hz

Power Consumption

110W, 1.44A, PF: .66

Light Source

LED

1x 60W RGBW 4-in-1 LED

8* 0.5W RGB 3-in-1 LEDs (Ring)

Thermal

Max. Operating Temp.

104 degrees F (40 degrees C) ambient

Movement Range

Pan

540 degree (8-16 bit resolution) / Infinite Pan

Tilt

270 degree (8-16 bit resolution) / Infinite Tilt

Control

Protocol

USITT DMX-512

DMX Channels

19/26 or 35-channel DMX modes

Input

3-pin XLR Male

Output

3-pin XLR Female

Other Operating Modes Standalone, Master/Slave, Auto, Sound Active

Warranty

2-year limited warranty, does not cover malfunction caused by

damage to LEDs.

Содержание Wink





















Результаты поиска

Содержание Wink

Отзывы:

Бренды по названию

Популярные бренды

Blizzard Lighting Wink, Руководство пользователя

Результаты поиска

Содержание Wink

Отзывы:

Бренды по названию

Популярные бренды