8
9
f e a t u r e s a n d c o n t r o l s
2 c h a m p B Z A - 2 3 6 0 . B Z A - 2 4 6 0
f e a t u r e s a n d s p e c i f i c a t i o n s
2 c h a m p B Z A - 2 3 6 0 . B Z A - 2 4 6 0
B Z A - 2 3 6 0
2 channel amplifier
frequency response
power supply voltage
output power @ 14.4v DC, 1KHz
RMS Power @ 4 Ohms
RMS Power @ 2 Ohms
Maximum Power Output
input sensitivity
low level inputs
high level inputs
100 Watts x 2
150 Watts x 2
700 Watts x 2
15 Hz-30 KHz
250mV
2.5V
14.4V DC Neg. Ground (10.5-16V)
maximum current draw
dimensions (W x H x L)
mm
inches
2-4 Ohms
15Ax2
4-8 Ohms
input impedance
low level inputs
high level inputs
10K Ohms
100 Ohms
matching speaker impedance
stereo mode
bridged mode
276 x 68 x 343
10.9 x 2.67 x 13.5
speaker connections
power terminals
power fuse
crossover mode selector
input level control
low pass frequency control
bass boost level
high pass frequency control
protection LED
power LED
high level inputs
low level inputs
remote bass boost
crossover mode selector
input level control
low pass frequency control
high pass frequency control
Remote Bass Boost
bass boost level control
low level inputs
high level inputs
power LED
protection LED
power fuse
power terminals
speaker connections
when used with normal, full range systems, set this switch to “FULL.” If
you wish to use the internal crossover to power a driver of specific frequency
range, use the “LOWPASS” or “HIGHPASS” settings.
use this control to match the outputs of your head unit to the amplifier.
Starting with your head unit set at about the 2 o’clock position, increase
the amp level control until distortion begins to occur, and reduce slightly
from this point.
when the crossover selector switch is in “low pass” mode, this control sets
the upper frequency limit for audio program sent to the speakers.
when the crossover selector switch is in “high pass” mode, this control
sets the lower frequency limit for audio program sent to the speakers.
Plug in the Remote Bass Boost Control wire in here.
this control permits adjustment of the bass level up to an increase of
approximately 18 dB.
this amp features gold-plated RCA input jacks for high impedance input.
Use these with car stereo output which uses RCA-type connector cables.
if your car stereo lacks RCA-type output jacks, you may connect speaker
output leads to these input connectors.
this indicator is illuminated when power is applied.
this indicator is illuminated when built-in protection circuitry is activated.
the fuse protects the amplifier and your car’s electrical system from short
circuit conditions.
use these connectors to deliver power, ground and remote turn-on control
to the amplifier.
these terminals are 14K gold plated to guarantee high conductivity and
minimum signal loss.
B Z A - 2 4 6 0
2 channel amplifier
125 Watts x 2
200 Watts x 2
800 Watts x 2
15Ax2
276 x 68 x 381
10.9 x 2.67 x 15
LINE
INPUT
MODE
LEVEL
BASS
BOOST
LOW
PASS
HIGH
PASS
R
L
FULL
LPF
HPF
PROTECT
POWER
R
L
MIN
MAX
0
18dB
80
2.5k
Hz
35
400
Hz
REMOTE
BASS
GND
12V
REM
BRIDGED
L
R
FUSE
B Z A - 2 3 6 0
B Z A - 2 4 6 0
