Blendtec PROFESSIONAL 750 Скачать руководство пользователя страница 4

Страница: 4 / 12

3.2

BLENDER JAR ASSEMBLY

The blender jar assembly consists of the blender jar, blade assembly, and lid�

• Jar: The jar is durable, BPA-free, and easy to clean�
• Blade Assembly: The uniquely designed stainless steel blade provides fast,

consistent blending�

• Lid: The lid seals liquids within the jar during blending�

NOTE: Filling the blender jar beyond the marked capacity is not recommended.

SECTION 4:

INSTALLATION & OPERATIONAL OVERVIEW
4.1

PROFESSIONAL 750™

4.1.1

INSTALLATION

Above Counter Installation

1� Place the blender on a flat, clean, and dry surface� Blender vents should be

unobstructed to allow proper cooling during use�

2� Make sure an outlet is available within two feet of the blender motor�
3� Place appropriately filled blender jar, with lid in place, onto blender base�
4� We recommend that surge protection be placed between the receptacle and

the blender motor on the circuit connected to the blender motor�

Preparation for In-Counter Installation

1� Identify the best place to install your blender� Consider proximity to ingredients,

available counter space, and access to a power outlet�

2� Ensure that the location meets all dimensional requirements (see Figure 3)�

a� The countertop must be no thicker than 1 1/4 inch (32 mm) to ensure

adequate ventilation�

NOTE: Ensure sufficient air circulation beneath the blender base. Hot air should

not be trapped beneath the counter top. Nothing should be stored within 3 inches

(76 mm) of the bottom of the motor.

3� Cut a hole in the counter top 4 ⅜ inches (111 mm) wide and 5 ⅞ inches (149

mm) long with the shorter side facing the operator (See Countertop Hole

Template or Figure 3)� Make sure all space requirements and measurements are

correct BEFORE cutting� It is recommended that you consult with a professional

before cutting�

In-Counter Installation

1� Remove the motor base from the motor base cover�
2� Slide the blender base into the new hole in your countertop, the LCD indicator

and touchpad facing the operator side of the blender� The rubber gasket on the

rim of the motor base should fit into the hole and rest lightly on the countertop�

3� Make sure the power switch is off� Plug the unit into a 120 volt outlet with

15 amp protection�

SECTION 2: UNPACKING

SAVE ALL PACKAGING MATERIALS AND INSTRUCTIONS FOR FUTURE USE

2.1

UNPACKING YOUR BLENDER

You should have received the following items:

• Professional series blender motor base
• Blender jar with lid

Additional literature may be included depending on package configuration�
1� Remove blender motor base, blender jar and lid from packaging�
2� Unwind the power cord�
3� Check for any packing material that may have blocked ventilation holes on the

underside of the blender motor base�

4� Inspect all items to ensure no damage occurred during shipment�
5� If any damage has occurred, contact Blendtec customer service (see page 17)

immediately�

2.2

RECORDING YOUR SERIAL NUMBER AND DATE OF PURCHASE

Record your blender motor serial number and date of purchase in the space below�

You will need these when contacting Blendtec for service or questions�
Motor Serial #(Found on bottom of motor base):_________________________
Date of Purchase: ______________________________________________
Purchased From: _______________________________________________

2.3

REGISTERING YOUR BLENDER

SECTION 3: GETTING TO KNOW YOUR BLENDER

(Refer to Figures 1 and 2 on Page 6)

3.1

BLENDER MOTOR BASE

• Smart Touch Interface: The interface consists of one-touch pre programmed

cycles and speeds, as well as Stop and Pulse buttons�

• Hardened Metal Drive Socket: This is where the jar couples with the motor to turn

the blade assembly� It is made of hardened metal�

• LCD Information Center: This displays how many blend cycles your blender has

run, remaining time during blends, and any error messages�