2 Installing batteries
Remove the battery cover from the rear of the remote control and
insert the AAA batteries which are supplied in the accessory pack.
Ensure that the polarity of the batteries is as shown in the battery
compartment. Replace the battery cover. The remote control is ready
for use.
Switch on the television using the power on/off switch located
on the TV. The standby light will show.
3 Connecting your set
Connect the TV to your power socket.
If you wish to use the TV to receive Freeview/Saorview channels,
connect the RF input from the TV to your outdoor Digital TV
aerial. If you do not wish to receive Freeview/Saorview, skip this
step.
4 Locating the Power Switch
5 First time installation
Register For Your
Manufacturers Warranty
Register your manufacturers guarantee
online within 14 days of purchase at
www.registertv.co.uk/blaupunkt
Regis
Manufa
Register your
online with
www.reg
Wall Mounting the TV
Image for illustration only.
1.
Remove the four screws that are supplied
in the wall mounting holes.
2.
The wall mount can now be easily
attached to the mounting holes on
the rear of the TV.
3.
Install the wall mounting bracket to the
television as advised by the bracket
manufacturer.
The picture shows the use of spacers, which
are not applicable to all sets/installations.
4 x
Used for attaching the stand neck
to the TV (fi g.1 to 3)
1 Fitting the stand
TV panel must be facing downwards.
For the stand installation, there is
one type of screw provided as shown
below.
To complete the stand installation you
will require a cross head screw driver.
Place the TV set on a fl at and
clean surface with the panel facing
downwards to avoid damage.
4 x
2
3
Place the TV set on a fl at and clean surface with the
panel facing downwards to avoid damage.
When the stand feet are installed correctly the stand
feet will be longest at the front of the TV and shortest
at the feet pointing away from each other.
When the stand feet are in the correct position, secure
the stand feet to the TV set using the 4 screws provided.
1
Introduction
When the set fi rst turns on, it enters the First Time Installation mode. This can be
restarted by restoring the set to default settings in the ‘About TV’ Menu.
Languages
Select your preferred on-screen display language. This will change the language in which
the menus and associated information is displayed in. When set up has been completed, to
change this press the [MENU] button and then select Settings > System Menu > Language
Country Selection
Select the correct fl ag for the country in which the set will be
used in. This will enable the set to correctly install the functions
applicable in the country of use.
Environment of Use
Home Mode:
For normal use, by default it is set to a power saving mode which
reduces the energy used by up to 25% (by reducing the power to the LED/LCD
panel). This can be changed in the picture mode settings.
Network setup
You can connect the TV to your broadband router or wireless network in order to take
advantage of the Smart functions. If you connect the TV to your router using an Ethernet
cable (recommended) this step will be skipped.
Set Up Netfl ix
If you have a Netfl ix account, it can be set up on the television
here. Once set up and validated, the First Time Installation returns
to the next step.
Tune in Channels
Choose to install terrestrial channels now or later.
Support Advice
Information regarding support is displayed for a little while.
Tuning continues and a progress bar is shown with the number of
channels found indicated below.
1
2
5
7
Basic installation steps are shown below. These may vary slightly depending on model.
Default Source
Select the source which you use the most. If Digital TV (Freeview) is chosen, then at
the next step, the set will tune in and default to Digital TV (Freeview). If one of the
other sources is selected, then the set will not tune in at this stage and default to
that input. If it is required to tune the set in later, press the [MENU] button and then
select Settings>Channels
Note:
In home mode,
the TV will switch off
automatically after 4
hours in the event that
no buttons are pressed on
the TV or remote control.
(You can change this
by pressing the [MENU]
button and then selecting
Settings>Time>Auto
Standby)
4
3
6
8
9
1
2
1
2
Setting up the TV set for the fi rst time
*The ethernet/LAN port is used for Digital TV services and Smart Functions
To obtain a copy of your Operating Instructions, please go to: https://www.umc-uk.co.uk/instruction-manuals/Blaupunkt-Television_information.html
or use this QR code:
